Mitsubishi Outlander GS45X. Manual — part 537
IGNITION SYSTEM
TSB Revision
ENGINE ELECTRICAL
16-47
<When special tool MB992273 is used>
1. Sufficiently apply the brake cleaner to the plug end.
NOTE: Repeatedly applying the brake cleaner is acceptable
during the cleaning.
2. Using special tool MB992273, intensively clean the
electrode for 1 to 2 minutes.
NOTE: Even if using strong force, the electrode is not dam-
aged.
NOTE: In case of insufficient cleaning, it is permissible to
take longer than 2 minutes for cleaning.
3. After the cleaning, sufficiently remove and then dry both of
the carbon and the brake cleaner on the plug, using a waste
cloth or air blowing.
CAMSHAFT POSITION SENSOR CHECK
M1163004400822
Refer to GROUP 13A, Multiport Fuel Injection (MFI) <2.4L
Engine>
− Multiport Fuel Injection (MFI) Diagnosis − Diagnostic
Trouble Code Procedures
− DTC P0340: Camshaft Position
. <2.4L>
Refer to GROUP 13B, Multiport Fuel Injection (MFI) <3.0L
Engine>
− Multiport Fuel Injection (MFI) Diagnosis − Diagnostic
Trouble Code Procedures
− DTC P0340: Camshaft Position
. <3.0L>
CRANKSHAFT POSITION SENSOR CHECK
M1163004500874
Refer to GROUP 13A, Multiport Fuel Injection (MFI) <2.4L
Engine>
− Multiport Fuel Injection (MFI) Diagnosis − Diagnostic
Trouble Code Procedures
− DTC P0335: Crankshaft Position
. <2.4L>
Refer to GROUP 13B, Multiport Fuel Injection (MFI) <3.0L
Engine>
− Multiport Fuel Injection (MFI) Diagnosis − Diagnostic
Trouble Code Procedures
− DTC P0335: Crankshaft Position
. <3.0L>
AK705045
MB992273
AD
IGNITION SYSTEM
TSB Revision
ENGINE ELECTRICAL
16-48
IGNITION COIL
REMOVAL AND INSTALLATION <2.4L ENGINE>
M1163004001504
AC506572AC
3.0 ± 0.5 N·m
27 ± 4 in-lb
10 ± 2 N·m
89 ± 17 in-lb
25 ± 5 N·m
19 ± 3 ft-lb
1
2
3
4
Removal steps
1.
Cylinder head cover center cover
2.
Ignition coil connector connection
3.
Ignition coil
4.
Spark plug
Removal steps (Continued)
IGNITION SYSTEM
TSB Revision
ENGINE ELECTRICAL
16-49
REMOVAL AND INSTALLATION <3.0L ENGINE>
M1163004001496
AC703803
2
3
4
5
6
7
9.5 ± 2.5 N·m
84 ± 22 in-lb
9.5 ± 2.5 N·m
84 ± 22 in-lb
18 ± 2 N·m
13 ± 2 ft-lb
18 ± 2 N·m
13 ± 2 ft-lb
3.0 ± 0.5 N·m
27 ± 4 in-lb
1
AB
Removal steps
1.
Engine cover
2.
Ignition coil connector connection
(Left bank)
3.
Ignition coil (Left bank)
4.
Spark plug (Left bank)
•
Intake manifold plenum (Refer to
GROUP 15, Intake Manifold
Plenum
5.
Ignition coil connector connection
(Right bank)
6.
Ignition coil (Right bank)
7.
Spark plug (Right bank)
Removal steps (Continued)
IGNITION SYSTEM
TSB Revision
ENGINE ELECTRICAL
16-50
CAMSHAFT POSITION SENSOR
REMOVAL AND INSTALLATION <2.4L ENGINE>
M1163003401402
AC611355AE
28 ± 8 N·m
21 ± 6 ft-lb
11 ± 1 N·m
98 ± 8 in-lb
1
2
3
4
5
6
7
8
9
N
N
11 ± 1 N·m
98 ± 8 in-lb
11 ± 1 N·m
98 ± 8 in-lb
11 ± 1 N·m
98 ± 8 in-lb
(Engine oil)
(Engine oil)
Removal steps <Exhaust side>
1.
Engine hanger
2.
Exhaust camshaft position sensor
connector connection
3.
Exhaust camshaft position sensor
4.
O-ring
Removal steps <Intake side>
•
Air cleaner cover and air cleaner
intake hose (Refer to GROUP 15,
Air Cleaner <2.4L
Engine>
).
5.
Control harness clamp
6.
Emission vacuum hose and pipe
assembly mounting bolt
7.
Intake camshaft position sensor
connector connection
8.
Intake camshaft position sensor
9.
O-ring
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст