Mitsubishi Outlander GS45X. Manual — part 222
PANIC ALARM
TSB Revision
CHASSIS ELECTRICAL
54A-885
STEP 2. Using scan tool MB991958, read the diagnostic
trouble code.
Check if DTC is set to the KOS-ECU <Vehicles with KOS> or
WCM <Vehicles with WCM>.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Turn the ignition switch to the "ON" position.
(2) Check whether the KOS or WCM related DTC is set.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES <vehicles with KOS> : Troubleshoot the KOS (Refer
to GROUP 42B, KOS
).
YES <vehicles with WCM> : Troubleshoot the WCM (Refer
to GROUP 42C, WCM
NO : Go to Step 3.
STEP 3. Check keyless operation system <KOS> or
keyless entry system <WCM>.
Q: Do keyless operation system <KOS> or keyless entry
system <WCM> work normally?
YES : Go to Step 4.
NO <vehicles with KOS> : Troubleshoot the KOS (Refer to
).
NO <vehicles with WCM> : Troubleshoot the WCM (Refer
to GROUP 42C, WCM
STEP 4. Using scan tool MB991958, check the
configuration function.
(1) Turn the ignition switch to the "ON" position.
(2) Use the ETACS-ECU customization function to check that
the "Panic alarm switch" is set to "Enable".
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the "Panic alarm switch" set to "Enable"?
YES : Replace the ETACS-ECU.
NO : Use the ETACS-ECU customization function to set
the "Panic alarm switch" to "Enable"(Refer to
).
ZC501967
AC404789
AC702802
MB991824
MB991827
MB991910
Data link
connector
AB
PANIC ALARM
TSB Revision
CHASSIS ELECTRICAL
54A-886
REMOVAL AND INSTALLATION
M1547002600066
Panic alarm system component parts
• Headlight assembly (refer to
• Horn (refer to GROUP 54A-Horn
ON-VEHICLE SERVICE
CUSTOMIZATION FUNCTION
M1547003400225
By operating the ETACS system or MMCS of scan
tool MB991958, the following functions can be pro-
grammed. The programmed information is held even
when the battery is disconnected.
Adjustment item
(scan tool
MB991958
display)
Adjustment item
Adjusting contents (scan tool
MB991958 display)
Adjusting contents
Panic alarm switch With/without panic
alarm function
Disable
Without function
Enable
With function (initial
condition)
80A-1
GROUP 80A
CONFIGURATION
DIAGRAMS
CONTENTS
OVERALL CONFIGURATION
DIAGRAM <2.4L ENGINE> . . . . . . . .
OVERALL CONFIGURATION
DIAGRAM <3.0L ENGINE> . . . . . . . .
HOW TO READ CONFIGURATION
DIAGRAMS . . . . . . . . . . . . . . . . . . . .
ENGINE COMPARTMENT
<2.4L ENGINE> . . . . . . . . . . . . . . . . .
ENGINE COMPARTMENT
<3.0L ENGINE> . . . . . . . . . . . . . . . . .
ENGINE AND TRANSAXLE
<2.4L ENGINE> . . . . . . . . . . . . . . . . .
ENGINE AND TRANSAXLE
<3.0L ENGINE> . . . . . . . . . . . . . . . . .
DASH PANEL . . . . . . . . . . . . . . . . . . .
FLOOR AND ROOF . . . . . . . . . . . . . .
DOOR . . . . . . . . . . . . . . . . . . . . . . . . .
OVERALL CONFIGURATION DIAGRAM <2.4L ENGINE>
TSB Revision
CONFIGURATION DIAGRAMS
80A-2
OVERALL CONFIGURATION DIAGRAM <2.4L ENGINE>
M1801000103104
NOTE:
.
1. This illustration shows only major wiring harnesses.
2. *: also equipped at the right side.
AC900418
AB
Instrument panel
wiring harness
Control wiring
harness
Roof wiring
harness
Liftgate wiring
harness
Rear bumper
wiring harness
Battery wiring
harness (+)
Fog light
wiring harness
Front wiring
harness
Front door
wiring harness
*
Curtain air bag
wiring harness
*
Rear door
wiring harness
*
Rear end
wiring harness
Floor wiring
harness
Rear display
wiring harness
Fuel wiring
harness
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст