Mitsubishi Outlander GS45X. Manual — part 1488
AIR BAG MODULE(S) AND CLOCK SPRING
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-447
3. Does the "SRS" warning light illuminate for approximately
seven seconds, and go out?
4. If yes, the SRS system is functioning properly. If not, refer to
.
INSPECTION
M1524002500767
.
AIR BAG MODULE CHECK
DANGER
Never attempt to measure the circuit resistance of the
air bag modules (squib), even if you are using the
specified tester. If the circuit resistance is measured
with a tester, accidental air bag deployment will
result, and possible serious personal injury.
WARNING
If any component damage is found during the follow-
ing inspection, replace the air bag module with a new
one. Dispose of the old one according to the specified
procedure (Refer to
).
1. Check the pad cover for dents, cracks or deformation.
2. Check the connectors for damage, the terminals for
deformation, and the harness for binding.
3. Check the air bag inflator case for dents, cracks or
deformation.
4. Install the air bag module (driver’s side) to the steering
wheel and check fit and alignment with the steering wheel.
5. Install the air bag module (front passenger’s side) to the
instrument panel and front deck crossmember and check fit
and alignment.
.
AC901647
SRS Warning light
AB
ZC601274
AC506240
AC701920
Squib connectors
Inflator case
Squib connectors
Inflator case
AB
<Driver's side>
<Passenger's side>
AIR BAG MODULE(S) AND CLOCK SPRING
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-448
FRONT SEATBACK ASSEMBLY WITH SIDE-AIR
BAG MODULE CHECK
DANGER
Never attempt to measure the circuit resistance of the
air bag module (squib), even if you are using the
specified tester. If the circuit resistance is measured
with a tester, accidental air bag deployment will
result, and possible serious personal injury.
WARNING
If any improper part is found during the following
inspection, replace the front seatback assembly with
a new one. Dispose of the old one according to the
specified procedure (Refer to
).
1. Check the air bag module deployment section for dents or
deformation.
2. Check the connector for damage, the terminals for
deformation, and the harness for binding.
.
CLOCK SPRING CHECK
If any malfunction is found in the following inspections, replace
the clock spring with a new one.
1. Check the connectors and protective tube for damage, and
the terminals for deformation.
2. Visually check the case for damage.
3. Check that the continuity exists between the following
connector terminals.
• C-204 connector terminal 1 and horn switch connector
• C-204 connector terminal 2 and C-202 connector terminal 5
• C-204 connector terminal 3 and C-202 connector terminal 4
• C-204 connector terminal 4 and C-202 connector terminal 3
• C-204 connector terminal 5 and C-202 connector terminal 2
• C-204 connector terminal 6 and C-202 connector terminal 1
AC701971
Side-airbag module
deployment section
AB
1 2
4
3
5
1 2 3 4 5 6
AC706417
Steering wheel audio remote
control switch connector
Driver's air bag
module connector
AK
C-204
C-204
C-202
C-202
Case
Protective tube
Horn switch
connector
AIR BAG MODULE(S) AND CLOCK SPRING
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-449
CAUTION
Do not directly insert a probe, etc. into the terminal from
the front of the connector.
4. Insert the special tool (MB992006) from behind the air bag
module connector of the C-205 driver's side.
5. Connect the circuit tester to the special tool as shown in the
figure, and check the continuity among terminal No. 1
− 2 or
No. 3
− 4.
AC306759AX
Clock spring
Air bag
module connector
(driver's side)
Digital
multi-meter
Extra fine probe
(MB992006)
Air bag module
connector
(driver's side)
(Rear view)
SIDE IMPACT SENSOR
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-450
SIDE IMPACT SENSOR
REMOVAL AND INSTALLATION
M1524004601235
WARNING
•
Never attempt to disassemble or repair the side impact sensor. If faulty, replace it.
•
Do not drop or subject the side impact sensor to impact or vibration. Replace the side
impact sensor, if dents, cracking, deformation, or rust are present.
•
Replace the side impact sensor after the side and curtain air bag has deployed.
Pre-removal Operation
• Turn the ignition key to the "LOCK" (OFF) position.
AC701972
1
<Rear>
12 ± 1 N·m
106 ± 8 in-lb
3
9.0 ± 1.0 N·m
80 ± 8 in-lb
Center pillar
Second seat belt
2
AC
<Front>
Side impact sensor (front)
removal steps
<<A>>
1.
Negative (
−) battery cable
connection
•
Center pillar trim, lower (Refer to
GROUP 52A, Interior Trim
•
Seat belt with pre-tensioner (Refer
to
<<B>>
•
Side impact sensor connector
connection
2.
Side impact sensor (Front)
Side impact sensor (front)
installation steps
>>A<<
•
Pre-installation inspection
>>B<<
2.
Side impact sensor (Front)
•
Side impact sensor connector
connection
•
Seat belt with pre-tensioner (Refer
to
•
Center pillar trim, lower (Refer to
GROUP 52A, Interior Trim
1.
Negative (
−) battery cable
connection
>>C<<
•
Post-installation inspection
Side impact sensor (Rear)
removal steps
<<A>>
1.
Negative (
−) battery cable
connection
•
Quarter trim, lower (Refer to
GROUP 52A, Interior Trim
<<B>>
•
Side impact sensor connector
connection
3.
Side impact sensor (Rear)
Side impact sensor (front)
installation steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст