Mitsubishi Outlander GS45X. Manual — part 1487
AIR BAG MODULE(S) AND CLOCK SPRING
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-443
<<C>> DRIVER’S AIR BAG MODULE
CONNECTOR REMOVAL
Slide the outer housing of the driver’s air bag module connector
in the arrow direction shown, and disconnect the connector.
.
<<D>> DRIVER’S AIR BAG MODULE ASSEMBLY
REMOVAL
WARNING
•
The air bag module must not be measured with
such equipment as an ohmmeter.
•
The air bag module must not be disassembled.
•
The removed air bag module should be stored in a
clean, dry place with the deployment surface fac-
ing up.
1. Using t-type long torx wrench (T30), a torx screw is loos-
ened completely and removed <CANADA, Except vehicles
with S-AWC>.
2. Loosen the torx screw and remove the air bag module
assembly <Vehicles with S-AWC (Except CANADA)>.
.
AC607302
AC600868
Outer housing of the driver's air bag
module connector
Horn connector
Lower column
cover
Driver's air bag
module connector
(4-pin, yellow)
AB
AC608854
AC609541AB
Equal to or more than
40mm (1.6 inch).
AIR BAG MODULE(S) AND CLOCK SPRING
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-444
<<E>> STEERING WHEEL ASSEMBLY REMOVAL
Use special tool MB990803 to remove the steering wheel.
.
<<F>> CLOCK SPRING REMOVAL
WARNING
The removed clock spring should be stored in a
clean, dry place.
.
<<G>> PASSENGER'S (FRONT) AIR BAG
MODULE CONNECTOR REMOVAL
Slide the outer housing of the passenger’s (front) air bag mod-
ule connector in the arrow direction shown, and disconnect the
connector.
.
<<H>> PASSENGER'S (FRONT) AIR BAG
MODULE REMOVAL
WARNING
•
The air bag module must not be measured with
such equipment as an ohmmeter.
•
The air bag module must not be disassembled.
•
The removed air bag module should be stored in a
clean, dry place with the deployment surface fac-
ing up.
Insert a slotted (
−) screwdriver or similar tool to the location
shown in the figure. After disengaging the tabs, remove the
front passenger's air bag module.
AC607307
MB990803
AB
AC506281AB
Passenger's (front) air bag module
connector (4-pin, yellow)
Harness side
connector
(4-pin, yellow)
Heater unit
AC506735
AB
Flat-tipped
screwdriver
Flat-tipped screwdriver
Passenger's (front)
air bag module
AIR BAG MODULE(S) AND CLOCK SPRING
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-445
INSTALLATION SERVICE POINTS
.
>>A<< PRE-INSTALLATION INSPECTION
WARNING
Dispose of air bag modules only according to the
specified procedure (Refer to
).
1. When installing the new air bag modules and clock spring,
).
2. Connect the negative (
−) battery cable.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
3. Connect scan tool MB991958 to the data link connector.
4. Turn the ignition switch to the “ON” position.
5. Check DTCs using scan tool MB991958 to ensure entire
SRS operates properly.
At this time, check that no DTC except B1B02, B1B06,
B1B0A and B1B0E are set.
DANGER
Wait at least 60 seconds after disconnecting the bat-
tery cable before doing any further work. (Refer to
).
WARNING
Battery posts, terminals and related accessories con-
tain lead and lead compounds. WASH HANDS AFTER
HANDLING.
6. Turn the ignition switch to the "LOCK" (OFF) position.
Disconnect the negative (
−) battery cable and tape the
terminal to prevent accidental connection and air bags
deployment.
.
>>B<< CLOCK SPRING INSTALLATION
1. Check that the front wheels are at the straight-ahead
position.
CAUTION
• If the center of the clock spring is not correctly aligned,
the steering wheel may not be turned fully or the cable
inside the clock spring may be broken, causing the
SRS air bag to be inoperative or operated incorrectly.
• When aligning the clock spring neutral position mark,
perform with the clock spring independently. If per-
formed with the steering wheel sensor installed, the
steering wheel sensor may be damaged.
2. Align the mating marks of the clock spring.
Alignment of mating marks
(1) Turn the clock spring clockwise fully.
(2) Turn the clock spring counterclockwise approximately
three and 1/2 turns to align the mating marks.
ZC501967
AC404789
AC701411AB
MB991824
MB991827
MB991910
Data link
connector
AIR BAG MODULE(S) AND CLOCK SPRING
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-446
(3) Check that the white roller can be seen from the window
for checking the neutral point when the mating marks are
aligned.
NOTE: If the white roller cannot be seen or black roller
can be seen, the neutral point is not aligned correctly.
(4) Install the clock spring to the column switch.
CAUTION
Be sure to align the steering wheel sensor neutral position
mark. If the neutral position marks are not aligned, the
steering wheel operation may damage the steering wheel
sensor.
3. Align the steering wheel sensor neutral position mark.
<Vehicle with ASC>
<Alignment of mating marks>
(1) When checking the neutral position check window of the
steering wheel sensor, if an arrow can be seen, turn to
the direction of the arrow, and align the neutral position
mark as shown in the figure.
(2) Install the steering wheel sensor to the column switch
assembly, maintaining the neutral position correctly.
(3) Install the column switch assembly to the vehicle,
maintaining the neutral position correctly.
.
>>C<< STEERING WHEEL ASSEMBLY/DRIVER’S
AIR BAG MODULE ASSEMBLY INSTALLATION
CAUTION
When installing the steering wheel and air bag module,
ensure that the harness of the clock spring does not
become caught or tangled.
1. Before installing the steering wheel and air bag module, turn
the vehicle’s front wheels to the straight-ahead position and
align the mating marks of the clock spring.
2. After securing the steering wheel, turn the steering wheel all
the way in both directions to confirm that the steering wheel
rotation is normal.
.
>>D<< DRIVER’S AIR BAG MODULE
CONNECTOR/HORN CONNECTOR CONNECTION
Connect the connector securely and route the harnesses not to
lie off the cover hole.
.
>>E<< POST-INSTALLATION INSPECTION
1. Reconnect the negative (
−) battery cable.
2. Turn the ignition switch to “ON” position.
AC705283AE
Mark for
checking
neutral point
Mating marks
AC308437AD
Steering wheel sensor
Mating mark
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст