Dodge Dakota (ND). Manual — part 1203
16. Seat the top of each of door seal to the door opening.
Club Cab, With Rear Jumper Seats
NOTE: Headliner for Quad Cab model shown. Club
Cab similar.
1.
CAUTION: Be careful not to crease the headlin-
er.Position the headliner (6) in the vehicle through
the door opening from which it was removed.
2. Connect the headliner wire harness connector (1)
to the center high mounted stop lamp.
3. Raise the rear of the headliner (7) to the roof panel
and install the two coat hooks, (Refer to 23 -
BODY/INTERIOR/COAT HOOK - INSTALLATION).
4. Raise the front of the headliner to the roof panel
and install the sun visor supports (3), (Refer to 23 -
BODY/INTERIOR/SUN
VISOR
SUPPORT
-
INSTALLATION).
5. Connect the wire harness connector (5) located at
the right A-pillar.
6. If equipped, connect the headliner wire harness connector (2) to the inside rear view mirror.
7. If equipped, install the overhead console, (Refer to 8 - ELECTRICAL/OVERHEAD CONSOLE - INSTALLATION).
8. Install the sun visors (4), (Refer to 23 - BODY/INTERIOR/SUN VISOR - INSTALLATION).
9. If equipped, install the front dome lamp, (Refer to 8 - ELECTRICAL/LAMPS/LIGHTING - INTERIOR/FRONT
DOME LAMP - INSTALLATION).
10. Install the A-pillar trim panels, (Refer to 23 -
BODY/INTERIOR/PANEL-A
PILLAR
TRIM
-
INSTALLATION).
11. If equipped, install the rear dome lamp, (Refer to 8 - ELECTRICAL/LAMPS/LIGHTING - INTERIOR/REAR
DOME LAMP - INSTALLATION).
12. Install the rear jumper seat headrest sleeves in the headliner.
13. Install the rear jumper seat headrests.
14. Install the cab back trim panel, (Refer to 23 - BODY/INTERIOR/PANEL-CAB BACK TRIM - INSTALLATION).
23 - 224
INTERIOR
ND
15. Install the upper C-pillar trim panels, (Refer to 23
-
BODY/INTERIOR/PANEL-C
PILLAR
UPPER
TRIM - INSTALLATION).
16. Position the seat belt turning loop and height
adjuster (3) bracket to the mounting holes in the
upper roof rail (1) and install the two screws (2)
that secure the bracket to the roof rail. Tighten the
screws to 39 N·m (29 ft. lbs.).
ND
INTERIOR
23 - 225
17. Install the upper door striker trim covers (3) as fol-
lows:
•
Position the trim cover (3) to the headliner (2)
opening around the door striker and engage the
retaining tabs that secure the cover to the roof
rail.
18. Install the front seat headrests.
19. Seat the top of each of door seal to the door opening.
Quad Cab
1.
CAUTION: Be careful not to crease the headlin-
er.Position the headliner in the vehicle through the
left door opening.
2. Connect the headliner wire harness connector (1)
to the center high mounted stop lamp.
3. Raise the rear of the headliner (7) to the roof panel
and install the two coat hooks, (Refer to 23 -
BODY/INTERIOR/COAT HOOK - INSTALLATION).
4. Raise the front of the headliner to the roof panel
and install the sun visor supports (3), (Refer to 23 -
BODY/INTERIOR/SUN
VISOR
SUPPORT
-
INSTALLATION).
5. Install the left front seat, (Refer to 23 - BODY/
SEATS/SEAT-FRONT - INSTALLATION).
6. Install the right front seat headrest.
7. Connect the wire harness connector (5) located at
the right A-pillar.
8. If equipped, connect the headliner wire harness connector (2) to the inside rear view mirror.
9. If equipped, install the overhead console, (Refer to 8 - ELECTRICAL/OVERHEAD CONSOLE - INSTALLATION).
10. Install the sun visors (4), (Refer to 23 - BODY/INTERIOR/SUN VISOR - INSTALLATION).
11. If equipped, install the front dome lamp, (Refer to 8 - ELECTRICAL/LAMPS/LIGHTING - INTERIOR/FRONT
DOME LAMP - INSTALLATION).
23 - 226
INTERIOR
ND
12. Install the A-pillar trim panels, (Refer to 23 -
BODY/INTERIOR/PANEL-A
PILLAR
TRIM
-
INSTALLATION).
13. If equipped, install the rear dome lamp, (Refer to 8 - ELECTRICAL/LAMPS/LIGHTING - INTERIOR/REAR
DOME LAMP - INSTALLATION).
14. Install the upper C-pillar trim panels, (Refer to 23
-
BODY/INTERIOR/PANEL-C
PILLAR
UPPER
TRIM - INSTALLATION).
ND
INTERIOR
23 - 227
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст