Dodge Dakota (ND). Manual — part 1128
REAR RETAINER
1. Apply 3 mm (1/8 in.) wide bead of Mopar
T
Gasket
Maker, or equivalent silicone adhesive sealer, to
mounting surface of rear retainer. Allow sealer to
set-up slightly before proceeding.
2. Install rear retainer on rear case. Tighten retainer
bolts to 27-34 N·m (20-25 ft. lbs.).
3. Install new output shaft bearing snap-ring (2). Lift
mainshaft slightly to seat snap-ring in shaft groove,
if necessary.
4. Apply 3 mm (1/8 in.) wide bead of Mopar
T
Gasket
Maker, or equivalent silicone adhesive sealer, to
mounting surface of extension housing. Allow
sealer to set-up slightly before proceeding.
5. Install extension housing on rear retainer.
6. Install extension housing bolts and tighten to 27-34
N·m (20-25 ft. lbs.).
INSTALLATION
1. Mount transfer case on a transmission jack.
2. Secure transfer case to jack with chains.
3. Position transfer case under vehicle.
4. Align transfer case and transmission shafts and
install transfer case (2) onto the transmission (1).
5. Install and tighten transfer case attaching nuts (3)
to 27-34 N·m (20-25 ft. lbs.) torque.
21 - 904
TRANSFER CASE - NV233
ND
6. Connect the vent hose (2) to the transfer case (3).
7. Connect the shift motor and mode sensor wiring
connectors (4). Secure wire harness to clips on
transfer case.
8. Align and connect the propeller shafts. (Refer to 3 -
DIFFERENTIAL
&
DRIVELINE/PROPELLER
SHAFT/PROPELLER SHAFT - INSTALLATION)
9. Fill transfer case with correct fluid. (Refer to 21 -
TRANSMISSION/TRANSAXLE/TRANSFER CASE/
FLUID - STANDARD PROCEDURE)
10. Install
rear
crossmember
and
skid
plate,
if
equipped. Tighten crossmember bolts to 41 N·m
(30 ft. lbs.) torque.
11. Remove transmission jack and support stand.
12. Lower vehicle and verify transfer case shift
operation.
SPECIFICATIONS - TRANSFER CASE - NV233
TORQUE SPECIFICATIONS
DESCRIPTION
N-m
Ft. Lbs.
In. Lbs.
Plug, Detent
16-24
12-18
-
Plug, Drain/Fill
20-34
15-25
-
Bolt, Front Brg. Retainer
16-25
12-18
-
Bolt, Case Half
27-34
20-25
-
Nut, Companion Flange
122-176
90-130
-
Bolt, Shift motor and Mode
Sensor Assembly
16-25
12-18
-
Bolt, Rear Retainer
27-34
20-25
-
Bolt, Extension Housing
27-34
20-25
-
Nut, Mounting
27-34
20-25
-
ND
TRANSFER CASE - NV233
21 - 905
SPECIAL TOOLS
TRANSFER CASE - NV233
Installer, Seal - 8143-A
Remover, Bushing - 8158
Installer, Bushing - 8157
Installer, Seal - D-163
Handle, Universal - C-4171
Installer, Seal - C-4210
Installer, Bearing - 5064
Installer, Bearing - 5065
21 - 906
TRANSFER CASE - NV233
ND
Installer, Bushing - 5066
Remover - L-4454
Cup - 8148
Installer, Seal - 7884
Installer, Pump Housing Seal - 7888
Wrench, Spanner - 6958
ND
TRANSFER CASE - NV233
21 - 907
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст