Chrysler Le Baron, Dodge Dynasty, Plymouth Acclaim. Manual — part 324
Fig. 9 Horn Diagnosis
8G - 4
HORNS
Ä
Fig. 10 High Line Steering Wheel
Fig. 11 Low Line Steering
Ä
HORNS
8G - 5
VEHICLE SPEED CONTROL
CONTENTS
page
page
CHECKING FOR FAULT CODE
. . . . . . . . . . . . . . 3
DIAGNOSIS PROCEDURES
. . . . . . . . . . . . . . . . 2
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . 1
INOPERATIVE SYSTEM
. . . . . . . . . . . . . . . . . . . 3
POWERTRAIN CONTROL MODULE ELECTRICAL
TEST
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ROAD TEST
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SERVO ELECTRICAL TESTS
. . . . . . . . . . . . . . . 4
SERVO UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SERVO VACUUM TEST
. . . . . . . . . . . . . . . . . . . 9
STOP LAMP VEHICLE SPEED CONTROL
SWITCH TEST
. . . . . . . . . . . . . . . . . . . . . . . . . 8
VACUUM SUPPLY TEST
. . . . . . . . . . . . . . . . . . 9
VEHICLE SPEED CONTROL SWITCH
REMOVAL
. . . . . . . . . . . . . . . . . . . . . . . . . . . 10
VEHICLE SPEED CONTROL SWITCH TEST
. . . 8
VEHICLE SPEED CONTROL ELECTRICAL
TESTS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
GENERAL INFORMATION
The vehicle speed control is electronically con-
trolled and vacuum operated. The electronic control
is integrated into the powertrain control module, lo-
cated next to battery. The controls are located on the
steering wheel and consist of the ON/OFF, RESUME/
ACCEL and SET/DECEL buttons (Fig. 1). For iden-
tification and location of the major components (Fig.
2 through 8).
The system is designed to operate at speeds above
35 mph (50 km/h).
WARNING: THE USE OF VEHICLE SPEED CON-
TROL IS NOT RECOMMENDED WHEN DRIVING
CONDITIONS DO NOT PERMIT MAINTAINING A
CONSTANT SPEED, SUCH AS IN HEAVY TRAFFIC
OR ON ROADS THAT ARE WINDING, ICY, SNOW
COVERED, OR SLIPPERY.
TO ACTIVATE: The ON/OFF button to the de-
pressed latched position, ON, the vehicle speed con-
trol function is now ready for use.
TO DEACTIVATE: A soft tap of the brake pedal,
normal brake application or depressing the clutch
pedal while the system is engaged will disengage ve-
hicle speed control without erasing memory. A sud-
den increase in engine rpm may be experienced if the
clutch pedal is depressed while the vehicle speed con-
trol is engaged. Pushing the ON/OFF button to the
unlatched position or turning off the ignition erases
the memory.
TO SET SPEED: When the vehicle has reached
the desired speed push the SET/DECEL button to en-
gage system which will then automatically maintain
the desired speed.
TO DECELERATE: When vehicle speed control is
engaged, holding the SET/DECEL button depressed
allows the vehicle to coast to a lower speed setting.
Fig. 1 Vehicle Speed Control Switch
Fig. 2 Vehicle Speed Control—2.2L and 2.5L
Ä
VEHICLE SPEED CONTROL
8H - 1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст