Chrysler Le Baron, Dodge Dynasty, Plymouth Acclaim. Manual — part 174
REAR POWER DOOR LOCK ACTUATOR
REMOVAL (FIG. 24)
(1) Remove door trim panel, silencer pad, and wa-
ter shield.
(2) Raise door glass to full up position.
(3) Remove door speaker, if equipped.
(4) Disconnect actuator rod from door latch assem-
bly.
(5) Remove screws holding power lock actuator to
inner door panel and separate from door.
INSTALLATION
Reverse the preceding operation.
REAR DOOR GLASS
REMOVAL (FIG. 25)
(1) Remove door trim panel and water shield.
(2) Position door glass half way up in door glass
opening.
(3) Pull upward firmly at the front upper corner of
glass to disengage lower glass guide from run chan-
nel.
(4) Insert door glass removal tool C-4867 between
the glass slide and division run channel retaining lip
at approximately 50 mm (2 in.) down from top rear-
ward corner of glass. Push handle of tool toward
glass to open channel. Pull forward on the glass to
separate the slide from the channel.
(5) Position glass inboard of the division channel.
Pivot top of glass rearward between division channel
and inner door panel.
(6) Separate regulator lift arm roller from glass lift
channel or remove bolt from regulator track, with
power windows.
(7) Remove door glass through opening at top of
door.
INSTALLATION
(1) Lower door glass into opening at top of door.
(2) Insert window regulator lift arm roller into
glass lift channel or install bolt to regulator track,
with power windows.
(3) Push top of glass rearward to snap top slide
into division run channel.
(4) Push downward at front of glass to snap bottom
slide into channel.
(5) Install water shield and trim panel.
REAR DOOR BELT MOULDING AND
WEATHERSTRIP
REMOVAL
(1) Remove trim panel, silencer pad, and water
shield.
Fig. 23 Rear Door Latch Assembly—Typical
Fig. 24-Rear Power Lock Actuator—Typical
Fig. 25 Rear Door Glass
23 - 106
AP-BODY
Ä
(2) Remove door glass.
(3) Remove screws holding belt moulding and
weatherstrip to outer door panel and separate moul-
ding from door.
INSTALLATION
Reverse the preceding operation.
REAR DOOR GLASS RUN WEATHERSTRIP
REMOVAL
(1) Remove door belt moulding and weatherstrip
assembly.
(2) Pull door glass run weatherstrip from forward
lower channel and upper door frame.
(3) Separate glass run weatherstrip from door.
INSTALLATION
(1) Insert glass run weatherstrip into top of glass
opening upper channel. Align molded corner of
weatherstrip to upper front corner of glass opening.
(2) Push weatherstrip into door frame window
opening.
(3) Install door belt moulding and weatherstrip as-
sembly.
REAR DOOR STATIONARY GLASS
STATIONARY GLASS REMOVAL
(1) Remove belt moulding and weatherstrip assem-
bly.
(2) Remove upper window opening moulding.
(3) Remove bolts and screws holding division chan-
nel and glass module to door assembly and separate
division channel from door frame.
(4) Separate stationary glass from division chan-
nel.
(5) Remove division channel through opening at
top of door.
STATIONARY GLASS INSTALLATION
Reverse the preceding operation.
REAR DOOR WINDOW REGULATOR/MANUAL
MANUAL WINDOW REGULATOR REMOVAL
(FIG. 26)
(1) Remove trim panel, silencer pad, and water
shield.
(2) Position door glass 150 mm (6 in.) up into glass
opening.
(3) Remove bolts holding window regulator to in-
ner door panel.
(4) Slide roller from window lift channel.
(5) Remove bolts holding reinforcement brace to
inner door panel.
(6) By hand, pull glass upward to 25 mm (1 in.)
from full up position. Using suitable tape, secure
door glass to upper window frame.
(7) Remove regulator assembly from door.
MANUAL WINDOW REGULATOR
INSTALLATION
Reverse the preceding operation.
REAR DOOR WINDOW REGULATOR/POWER
POWER WINDOW REGULATOR REMOVAL
(1) Remove trim panel and water shield.
(2) Position door glass 150 mm (6 in.) up into glass
opening.
(3) Remove bolts holding window regulator lift
bracket to door glass.
(4) Remove fasteners holding power window regu-
lator to inner door panel.
(5) By hand, pull glass upward to 25 mm (1 in.)
from full up position. Using suitable tape, secure
door glass to upper window frame.
(6) Remove regulator assembly from door.
POWER WINDOW REGULATOR INSTALLATION
Reverse the preceding operation.
DOOR OPENING WEATHERSTRIPS
FRONT OR REAR DOOR OPENING
WEATHERSTRIP REMOVAL (FIG. 27)
(1) Remove interior trim as necessary to gain ac-
cess to door opening weatherstrip.
(2) Pull weatherstrip from pinch flange around
door opening.
FRONT OR REAR DOOR OPENING
WEATHERSTRIP INSTALLATION
(1) Locate the middle to the weatherstrip at the
center of the upper pinch flange. Push weatherstrip
onto pinch flange at the top corner near the B-pillar.
Fig. 26 Rear Door Manual Window
Regulator—Typical
Ä
AP-BODY
23 - 107
(2) When the weatherstrip has been installed down
the door opening to the sill pinch flange, mate the
ends of the weatherstrip together and finish install-
ing.
QUARTER GLASS WINDOW
REMOVAL (FIG. 28)
(1) Remove quarter trim panel as necessary to
gain access to quarter glass fasteners.
(2) Remove quarter window opening moulding.
(3) Remove screw holding quarter glass to retain-
ing bracket.
(4) Remove rivets holding quarter glass to B-pillar
with a 6 mm (0.250 in.) drill.
INSTALLATION
Reverse the preceding operation.
QUARTER GLASS WEATHERSTRIP
REMOVAL (FIG. 29)
(1) Remove quarter trim panel as necessary to
gain access to quarter glass fasteners.
(2) Remove screw holding quarter glass to retain-
ing bracket.
(3) Hinge quarter glass away from weatherstrip.
(4) Remove quarter glass weatherstrip from pinch
flange.
INSTALLATION
Reverse the preceding operation.
BODY SIDE MOULDING AND APPLIQUE
STICK-ON BODY SIDE MOULDING REMOVAL
AND INSTALLATION
(1) Warm the effected stick-on moulding and body
metal to approximately 38°C (100°F) using a suitable
heat lamp or heat gun.
(2) Pull stick-on moulding from painted surface.
(3) Remove adhesive tape residue from painted
surface of vehicle.
(4) If moulding is to be reused, Remove tape resi-
due from moulding. Clean back of moulding with Mo-
par,
Super
Kleen
solvent
or
equivalent.
Wipe
moulding dry with lint free cloth. Apply new body
side moulding (two sided adhesive) tape to back of
moulding.
(5) Clean body surface with Mopar, Super Kleen
solvent or equivalent. Wipe surface dry with lint free
cloth.
(6) Apply a length of masking tape on the body,
parallel to the top edge of the moulding to use as a
guide, if necessary.
(7) Remove protective cover from tape on back of
moulding. Apply moulding to body below the mask-
ing tape guide.
(8) Remove masking tape guide and heat body and
moulding, see step one. Firmly press moulding to
body surface to assure adhesion.
Fig. 27 Door Opening Weatherstrips—Typical
Fig. 28 Quarter Glass—AP-24 Body
Fig. 29 Quarter Glass Weatherstrip—AP-24 Body
23 - 108
AP-BODY
Ä
APPLIQUE MOULDING AND RETAINER
REMOVAL
(1) Remove screws holding applique to rocker
panel from under vehicle.
(2) Lift applique upward to separate from retain-
ing channel.
(3) Remove pop-rivets holding retainer to rocker
panel using a suitable drill.
APPLIQUE MOULDING AND RETAINER
INSTALLATION
(1) Install applique retainer on rocker panel with
pop-rivets. Paint or undercoat bare metal surfaces to
avoid rust.
(2) Hook top of applique over retainer channel and
install screws under rocker panel.
COWL PANEL TRIM AND SCUFF PLATES
COWL PANEL AND DOOR OPENING SCUFF
PLATE REMOVAL (FIG. 30 OR 31)
(1) Open front door.
(2) Remove screw holding trim panel to cowl for-
ward of the front door opening.
(3) Remove screws holding scuff plate to door sill.
(4) Separate cowl panel trim and scuff plate from
vehicle.
COWL PANEL AND DOOR OPENING SCUFF
PLATE INSTALLATION
Reverse the preceding operation.
A-PILLAR AND ROOF RAIL MOULDINGS
A-PILLAR MOULDING REMOVAL (FIG. 30 OR
31)
(1) Open front door.
(2) Disengage clips holding A-pillar moulding to
roof rail above door opening.
(3) Slide A-pillar moulding upward and pull rear-
ward to separate moulding from A-pillar.
A-PILLAR MOULDING INSTALLATION
Reverse the preceding operation.
REAR DOOR ROOF RAIL MOULDING
REMOVAL—AP-44 BODY (FIG. 30)
(1) Open rear door.
(2) Disengage clips holding roof rail moulding to
roof rail above rear door opening.
(3) Separate moulding from vehicle.
REAR DOOR ROOF RAIL MOULDING
INSTALLATION—AP-44 BODY
Reverse the preceding operation.
B-PILLAR TRIM PANEL—AP-44 Body
REMOVAL (FIG. 30)
(1) Remove roof rail mouldings and scuff plates as
necessary.
(2) Remove shoulder harness turning loop cover.
Remove bolt holding turning loop to B-pillar.
(3) Remove bolt holding seat belt to floor below
B-pillar.
(4) Lift B-pillar trim off door opening sill weather-
strips and push inward.
(5) Slide B-pillar trim downward as far as possible
and separate trim from B-pillar.
INSTALLATION
Reverse the preceding operation.
UPPER QUARTER TRIM PANEL—AP-44 BODY
REMOVAL (FIG. 30)
(1) Remove roof rail mouldings as necessary.
(2) Remove shoulder harness turning loop cover.
Remove bolt holding turning loop to quarter panel.
(3) Remove rear seat as necessary to gain access to
quarter trim fasteners.
(4) Remove screws holding rear header moulding
to roof as necessary to clear quarter removal path.
(5) Remove screws holding upper quarter trim
panel to quarter panel.
(6) Disengage hook and loop fastener holding trim
to quarter panel.
(7) Pull trim panel forward and separate from ve-
hicle.
INSTALLATION
Reverse the preceding operation.
LOWER QUARTER TRIM PANEL—AP-44 BODY
REMOVAL (FIG. 30)
(1) Open rear door.
(2) Remove rear seat as necessary to gain access to
quarter trim fasteners.
(3) Remove screw holding lower quarter trim panel
to quarter panel.
(4) Separate lower quarter trim panel from vehicle.
INSTALLATION
Reverse the preceding operation.
QUARTER TRIM PANEL—AP-44 BODY
REMOVAL (FIG. 31)
(1) Remove roof rail mouldings and scuff plates as
necessary.
(2) Remove shoulder harness turning loop cover.
Remove bolt holding turning loop to quarter panel.
(3) Remove rear seat cushion, back, and rear bol-
ster.
Ä
AP-BODY
23 - 109
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст