Chrysler Le Baron, Dodge Dynasty, Plymouth Acclaim. Manual — part 176
INSTALLATION
Reverse The preceding operation.
HEAD LINING
REMOVAL (FIG. 41)
(1) Disconnect battery negative cable.
(2) Pull dome lamp downward to disengage from
retaining ring in head lining. Separate lens from
lamp body and remove bulb. Separate bulb holder
from lamp body. Remove attaching screw holding re-
taining ring to roof bow.
(3) Remove screws holding coat hooks to roof above
rear doors.
(4) Remove roof rail and A-pillar mouldings.
(5) Remove screws holding sun visors to roof
header and disconnect wire connector, if equipped.
Remove inboard sun visor hangers.
(6) Remove overhead console, if equipped.
(7) Pull front reading lamp downward to disengage
from retaining ring in head lining and disconnect
wire connector. Remove screws holding retaining
ring to roof header.
(8) Remove pinch welt holding headlining to sun
roof opening, if equipped.
(9) Remove inside rear view mirror from wind-
shield bracket if necessary.
(10) Disengage hook and loop fasteners holding
head lining to roof above rear window and slide head
lining forward about 25 mm (1 in.).
(11) Shift the front of head lining to one side to
pull head lining from behind B-pillar trim. Pull head
lining from behind other B-pillar trim.
(12) Allow front of head lining to drop downward.
Slide head lining forward from behind quarter panel
trim.
(13) Remove head lining from vehicle.
INSTALLATION
Reverse the preceding operation.
SUN ROOF WEATHERSTRIP
REMOVAL (FIG. 42)
(1) Remove sun roof sunshade and glass. Refer to
Owner’s Manual for instructions.
(2) Pull weatherstrip from pinch flange around sun
roof opening.
INSTALLATION
Reverse the preceding operation.
SUN ROOF AIR DEFLECTOR
REMOVAL (FIG. 42)
(1) Remove sun roof sunshade and glass. Refer to
Owner’s Manual for instructions.
Fig. 39 Floor Carpet and Silencers—Typical
Fig. 40 Overhead Console—Typical
Fig. 41 Head Lining—Typical
23 - 114
AP-BODY
Ä
(2) Disengage snap-on linkage at rear of air deflec-
tor in sun roof opening.
(3) Remove screws holding air deflector to front of
sun roof opening.
INSTALLATION
Reverse the preceding operation.
SUN ROOF DRAIN TUBES
REMOVAL (FIG. 42)
(1) Remove head lining as necessary.
(2) Remove A-pillar or B-pillar trim covers as nec-
essary.
(3) Remove cowl panel and sill plate trim as neces-
sary.
(4) Disconnect effected drain tube from nipple at
sun roof opening.
(5) Pull drain tube upward to remove from pillar
involved.
INSTALLATION
Reverse the preceding operation. Route the tube to
avoid kinks or puncture from sharp edges.
LIFT GATE REMOTE RELEASE CABLE
REMOVAL
(1) Remove interior trim as necessary to gain ac-
cess to release cables.
(2) Remove left front door scuff plate.
(3) Remove screw holding trim cover to release ca-
ble handle and separate cover from handle.
(4) Remove screw holding release handle to door
sill.
(5) Pry open retainer tab holding cable core end in
handle pivot. Pry cable case end from handle.
(6) Remove trunk lining as necessary to gain ac-
cess to the release cable.
(7) Disconnect cable end from latch.
(8) Separate cable from vehicle.
INSTALLATION
Reverse the preceding operation.
REAR WINDOW GLASS
REMOVAL (FIG. 43)
(1) Raise lift gate to up position.
(2) Remove screws holding outward edges to rear
window moulding to lift gate frame.
(3) Position protective card board covers along the
top of the quarter panels to protect painted surfaces.
Fig. 42 Sun Roof
Ä
AP-BODY
23 - 115
(4) Support lift gate in the up position and remove
bolts holding lift gate hinge closed. Lower lift gate to
opening weatherstrip.
(5) Remove screws holding top of rear window
moulding to lift gate frame. Separate moulding from
lift gate.
(6) Pull lower rear window moulding from under
glass.
(7) Cut urethane bonding from around rear win-
dow. Refer to Windshield section of this group.
INSTALLATION
Prepare the lift gate fence and rear window as de-
scribed in the Windshield Installation section of this
group. Reverse the removal operation.
LIFT GATE LUGGAGE RACK
REMOVAL (FIG. 44)
(1) Remove screws holding cross bar to outboard
skid strips.
(2) Pry rubber inserts from skid strips.
(3) Remove screws holding skid strips to lift gate.
INSTALLATION
Reverse the preceding operation
Fig. 43 Rear Window Glass
Fig. 44 Lift Gate Luggage Rack
23 - 116
AP-BODY
Ä
AP/27-VEHICLE CONVERTIBLE BODY COMPONENT SERVICE
INDEX
page
page
A-Pillar and Windshield Header Weatherstrip
. . . . . . . . . . . . . . . 131
. . . . . . . . . . . . . . . . . . . 118
. . . . . . . . . . . . . . . 131
. . . . . . . . . . . . . . . . . . . . 131
. . . . . . . . . . . . . . . . . 127
. . . . . . . . . . . . . . . . . . . . . . 128
. . . . . . . . . . . . . . . . . . . . . . . 121
. . . . . . . . . . . . . . . . . 120
. . . . . . . . . . . . . . . . . . . . 132
Front Door Belt Moulding and Weatherstrip
. . . . . . . . . . . . . . . . . . . . . . . . 125
Front Door Stationary Glass and Division
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Front Door Stationary Glass Channel
. . . . . . . . . . . . . . . . . . . . . . . . . . 126
Front Door Striker Guide Socket
. . . . . . . . . . . . . . . . . . 128
. . . . . . . . . . . . . . . . . . . . . . 117
Quarter Glass and Roller Bracket
. . . . . . . . . . . . . . . 129
. . . . . . . . . . . . . . . . . . . . . . 128
. . . . . . . . . . . . . . . . . . . . . . . . . 121
. . . . . . . . . . . . . . . . . . . . . . . . . 128
. . . . . . . . . . . . . . . . . . 129
. . . . . . . . . . . . . . . . . . . . . 132
. . . . . . . . . . . . . . . . . . . . . . . . . . 122
. . . . . . . . . . . . . . . . . . . . . . . . . . . 121
. . . . . . . . . . . . . . . . . . . 118
Roof Rail Weatherstrip Retainer
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Stationary Quarter Glass and Weatherstrip
. . . . . . . . . . . . . . . . . . . . . . . . . 120
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
. . . . . . . . . . . . . . . . . . . 118
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
. . . . . . . . . . . . . . . . . . . 122
. . . . . . . . . . . . . . . . . . . . 132
. . . . . . . . . . . . . . . . . . . . . . 132
. . . . . . . . . . . . . . . . . . . . . . . . 130
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
. . . . . . . . . . . . . . . . . . . . . . 130
. . . . . . . . . . . . . . . . . . . . . . . . 129
. . . . . . . . . . . . . . . 130
. . . . . . . . . . . . . . . . . 117
. . . . . . . . . . . . . . . 117
GENERAL INFORMATION
This section will cover components that are unique
to the AP-vehicle convertible. All components that
are common to the AP-vehicle two door hardtop are
covered in the AP-Vehicle Body Components section.
WINDSHIELD HEADER MOULDING
REMOVAL (FIG. 1)
(1) Remove windshield header lining.
(2) Remove nuts holding moulding to windshield
header.
(3) Separate windshield header moulding from ve-
hicle.
INSTALLATION
Apply sealing putty around mounting studs on
back of moulding and reverse the removal operation.
WINDSHIELD HEADER LINING
REMOVAL (FIG. 1)
(1) Remove sun visors and inner sun visor hanger
clips.
(2) Remove upper A-pillar trim covers.
(3) Remove dome lamp.
(4) Separate header lining from vehicle.
INSTALLATION
Reverse the preceding operation.
A-PILLAR AND WINDSHIELD HEADER
WEATHERSTRIP
REMOVAL (FIG. 2)
(1) Remove upper and lower A-pillar trim covers.
(2) Remove header lining and moulding.
(3) Pull A-pillar door opening weatherstrip from
pinch flange.
(4) Pull drip rail weatherstrip from drip rail next
to windshield.
Fig. 1 Windshield Header Moulding
Ä
AP/27 CONVERTIBLE
23 - 117
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст