Dodge Ram Truck 1500-2500-3500. Manual — part 1953
3. Install the three inserts (1 and 3) into the floor con-
sole (4).
4. Position the manual transmission gear shift boot or
storage bin (2) (depending on application) onto the
floor console and engage the retaining tabs.
5. If equipped with a manual transmission, install the
transmission gear shift lever extension.
6. If equipped, install the 4WD gear shift boot (Refer
to 23 - BODY/INTERIOR/4WD FLOOR SHIFT
BOOT - INSTALLATION).
HEADLINER
REMOVAL
NOTE: Headliner for Quad Cab model shown. Reg-
ular cab similar.
1. Remove the A-pillar trim panels (Refer to 23 -
BODY/INTERIOR/A-PILLAR TRIM - REMOVAL).
2. Remove the upper B-pillar trim panels (Refer to 23
-
BODY/INTERIOR/B-PILLAR
UPPER
TRIM
-
REMOVAL).
3. On Quad Cab models, remove the upper C-pillar
trim panels (Refer to 23 - BODY/INTERIOR/C-PIL-
LAR TRIM - REMOVAL).
4. Disconnect the wire harness connector (1) located
at the left A-pillar from the headliner wire harness
(2).
5. Disconnect the headliner wire harness connector
(3) from the inside rear view mirror.
6. Remove the overhead console (Refer to 8 - ELEC-
TRICAL/OVERHEAD CONSOLE - REMOVAL).
7. Remove the sun visors (4) (Refer to 23 - BODY/INTERIOR/SUN VISOR - REMOVAL).
8. Remove the sun visor supports (5) (Refer to 23 - BODY/INTERIOR/SUN VISOR SUPPORT - REMOVAL).
9. Remove the dome lamp (6) (Refer to 8 - ELECTRICAL/LAMPS/LIGHTING - INTERIOR/DOME LAMP -
REMOVAL).
10. Remove the two coat hooks (7) (Refer to 23 - BODY/INTERIOR/COAT HOOK - REMOVAL).
11. Lower the rear of the headliner (9) downward from the roof panel (9) and disconnect the headliner wire harness
connector (8) from the center high mounted stop lamp.
12. Lower the front of the headliner downward and remove the headliner through the passenger door opening.
23 - 166
INTERIOR
DR/DH
INSTALLATION
NOTE: Headliner for Quad Cab model shown. Reg-
ular cab similar.
1. Position the headliner (9) into the vehicle through
the passenger door opening.
2. Connect the headliner wire harness connector (8)
to the center high mounted stop lamp.
3. Raise the rear of the headliner upward and install
the two coat hooks (7) (Refer to 23 - BODY/INTE-
RIOR/COAT HOOK - INSTALLATION).
4. Raise the front of the headliner upward and install
the sun visor supports (5) (Refer to 23 - BODY/IN-
TERIOR/SUN
VISOR
SUPPORT
-
INSTALLA-
TION).
5. Install the sun visors (4) (Refer to 23 - BODY/IN-
TERIOR/SUN VISOR - INSTALLATION).
6. Install the dome lamp (6) (Refer to 8 - ELECTRI-
CAL/LAMPS/LIGHTING - INTERIOR/DOME LAMP
- INSTALLATION).
7. Install the overhead console (Refer to 8 - ELECTRICAL/OVERHEAD CONSOLE - INSTALLATION).
8. Connect the headliner wire harness connector (3) to the inside rear view mirror
9. Connect the headliner wire harness (2) to the wire harness connector (1) located at the left A-pillar.
10. On Quad Cab models, install the upper C-pillar trim panel (Refer to 23 - BODY/INTERIOR/C-PILLAR TRIM -
INSTALLATION).
11. Install the upper B-pillar trim panels (Refer to 23 - BODY/INTERIOR/B-PILLAR UPPER TRIM - INSTALLATION).
12. Install the upper A-pillar trim panels. (Refer to 23 - BODY/INTERIOR/A-PILLAR TRIM - INSTALLATION).
LOAD FLOOR
REMOVAL
1. Move the rear seat cushion (1) to the up position.
2. Remove the two nuts (2) that secure the rear of the
load floor (3) to the floor panel.
DR/DH
INTERIOR
23 - 167
3. Move the load floor (2) to the up position.
4. Remove the two bolts (3) that secure the load floor
to the floor panel (1) and remove the load floor.
5. If required, remove the support cylinder (4) (Refer
to 23 - BODY/INTERIOR/LOAD FLOOR SUPPORT
CYLINDER - REMOVAL).
INSTALLATION
1. If removed, install the load floor support cylinder (4)
(Refer to 23 - BODY/INTERIOR/LOAD FLOOR
SUPPORT CYLINDER - INSTALLATION).
2. Position the load floor (2) into the vehicle and
install the two bolts (3) that secure it to the floor
panel (1). Tighten the bolts to 40 N·m (29 ft. lbs.).
23 - 168
INTERIOR
DR/DH
3. Move the load floor (3) to the down position and
install the two nuts (2) that secure the load floor to
the floor panel. Tighten the nuts to 25 N·m (18 ft.
lbs.).
4. Move the rear seat cushion (1) to the down
position.
LOAD FLOOR SUPPORT CYLINDER
REMOVAL
1. Open the load floor (2).
2. Remove the snap clips and retaining pins (1).
3. Remove the support cylinder (3).
DR/DH
INTERIOR
23 - 169
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст