Dodge Ram Truck 1500-2500-3500. Manual — part 1954
INSTALLATION
NOTE: Install the support cylinder with the cylin-
der end connected at the top as shown.
1. Position the load floor support cylinder (3) onto the
load floor (2).
2. Install the retaining pins and snap clips (1).
REAR CAB BACK PANEL TRIM
REMOVAL
1. If equipped, remove the three bolts (1) that secure
the rear storage compartment (2) to the floor panel
(3) and remove the storage compartment from the
rear cab trim panel (4).
23 - 170
INTERIOR
DR/DH
2. If equipped, using a trim stick C-4755 or equiva-
lent, disengage the latch (4) for the utility hook
cover (3) and open the cover to gain access to the
screw (1) that secures the utility hook (2) to the
rear cab back panel.
3. On Regular cab models, remove the lower B-pillar
trim panels (Refer to 23 - BODY/INTERIOR/B-PIL-
LAR LOWER TRIM - REMOVAL).
4. On Regular cab models, remove the utility hook (3)
or the storage bin latch (4) (depending on applica-
tion) from the rear cab trim panel (1) and remove
the trim panel.
5. On Quad Cab models, remove the child seat tether
straps from the rear cab back panel (2) (Refer to 8
- ELECTRICAL/RESTRAINTS/CHILD TETHER -
REMOVAL).
6. On Quad Cab models, remove the center seat belt
trim
bezel
(Refer
to
8
-
ELECTRICAL/RE-
STRAINTS/SEAT
BELT
&
RETRACTOR
-
REMOVAL).
7. On Quad Cab models, remove the lower C-pillar
trim panels (Refer to 23 - BODY/INTERIOR/C-PIL-
LAR TRIM - REMOVAL).
8. On Quad Cab models, remove the two push-pin
fasteners (1 and 4) that secure the rear cab trim
panel (3) to the rear cab back panel and remove
the trim panel.
DR/DH
INTERIOR
23 - 171
INSTALLATION
1. On Quad Cab models, position the rear cab trim
panel (3) onto the rear cab back panel (2) and
install the two push-pin fasteners (1 and 4).
2. On Quad Cab models, install the lower C-pillar trim
panels (Refer to 23 - BODY/INTERIOR/C-PILLAR
TRIM - INSTALLATION).
3. On Quad Cab models, install the center seat belt
trim
bezel
(Refer
to
8
-
ELECTRICAL/RE-
STRAINTS/SEAT BELT & RETRACTOR - INSTAL-
LATION.
4. On Quad Cab models, install the child seat tether
straps (Refer to 8 - ELECTRICAL/RESTRAINTS/
CHILD TETHER - INSTALLATION).
5. On Regular cab models, position the rear cab trim
panel (1) onto the rear cab back panel (2) and
install the utility hook (3) or the storage bin latch
(4) (depending on application).
6. On Regular cab models, install the lower B-pillar
trim panels (Refer to 23 - BODY/INTERIOR/B-PIL-
LAR LOWER TRIM - INSTALLATION).
7. If equipped, position the rear storage compartment
(2) onto the rear cab trim panel (4) and install the
three bolts (1). Tighten the bolts to 6 N·m (55 in.
lbs.).
23 - 172
INTERIOR
DR/DH
REAR DOOR SILL TRIM COVER
REMOVAL
1. Using a trim stick C-4755 or equivalent, disengage
the retaining tabs of the sill trim panel (1) from the
retainer clips in the rear door sill (2) and remove
the trim panel.
INSTALLATION
1. Position the sill trim panel (1) onto the rear door sill
(2).
2. Engage the retaining tabs that secure the sill trim
panel to the rear door sill.
REAR VIEW MIRROR
REMOVAL
1. If equipped, disconnect the wire harness connector
(1) from the rear view mirror (3).
2. Loosen the set screw (2) that secures the rear view
mirror to the mounting bracket (4).
3. Slide the base of the rear view mirror upward and
remove the mirror from the mounting bracket.
4. If required, remove the mirror mounting bracket
from the windshield (5).
DR/DH
INTERIOR
23 - 173
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст