Dodge Dakota (R1). Manual — part 770
(5) Simultaneously lift upward and outward to
release retainer steps from inner door panel (Fig. 14).
(6) Disengage inside handle linkage rod from
inside handle.
(7) Disconnect speaker harness wire connector
(Fig. 15).
(8) Disengage clips attaching power window/lock
switch panel to door trim panel. Disengage wire con-
nector from switch panel, if equipped (Fig. 16).
(9) Separate door trim panel from vehicle.
INSTALLATION
(1) Position trim panel at door.
(2) Engage wire connector for window/lock switch
panel, if equipped. Engage clips attaching power win-
dow/lock switch panel to door trim panel.
(3) Engage
power
mirror
wire
connector,
if
equipped.
(4) Connect speaker harness wire connector.
(5) Engage inside handle linkage rod to inside
handle.
(6) Align trim panel retainer steps with inner door
panel and slide trim panel into place.
Fig. 11 Window Crank—Typical
1 - WINDOW CRANK REMOVAL TOOL
2 - WINDOW CRANK
Fig. 12 Door Trim Panel
1 - TRIM PANEL
Fig. 13 Trim Panel Screw
1 - TRIM PANEL
2 - INSIDE DOOR HANDLE
3 - INSIDE DOOR HANDLE BRACKET
Fig. 14 Trim Panel Retainer
1 - TRIM PANEL
2 - RETAINER STEP
3 - INNER DOOR PANEL
23 - 68
DOOR - FRONT
AN
TRIM PANEL (Continued)
(7) Install screws attaching trim panel to door.
(8) Install window crank, if equipped.
FRONT DOOR WATERDAM
REMOVAL
(1) Remove the trim panel from the door.
(2) Carefully separate the waterdam from the door
inner panel at the areas with adhesive (Fig. 17).
Remove the waterdam from the door inner panel.
INSTALLATION
(1) Apply an appropriate adhesive/sealant to the
waterdam edges before installing it.
(2) Position the waterdam on the door inner panel
and press it inward at the areas with the adhesive to
attach it to the inner panel.
(3) Ensure that the retainer step pockets are posi-
tion correctly in the door inner panel.
(4) Install the door trim panel.
Fig. 15 Speaker And Power Mirror Connector
1 - SPEAKER CONNECTOR
Fig. 16 Power Door Lock/Window Connector
1 - TRIM PANEL SWITCH BEZEL OPENING
2 - WIRE HARNESS CONNECTOR
3 - SWITCH AND BEZEL UNIT
Fig. 17 Water Dam
1 - STUFFERS
2 - RETAINER STEP POCKETS
3 - WATER DAM
AN
DOOR - FRONT
23 - 69
TRIM PANEL (Continued)
FRONT DOOR WINDOW
REGULATOR
REMOVAL
(1) Remove door trim panel.
(2) Remove water dam as necessary to access win-
dow regulator.
(3) Remove glass from door.
(4) Disengage power window motor wire connector
from door harness, if equipped (Fig. 18).
(5) Loosen bolts in slotted holes attaching regula-
tor to door inner panel (Fig. 19).
(6) Remove bolts attaching window regulator to
inner door panel.
(7) Extract window regulator through access hole
in inner door panel.
(8) Separate window regulator from door panel.
INSTALLATION
(1) Position regulator in door and align bolts with
slotted holes in door inner panel.
(2) Install bolts attaching window regulator to
inner door panel.
(3) Engage power window motor wire connector to
door harness, if equipped.
(4) Install glass in door.
(5) Install outer belt weatherstrip.
(6) Install inner belt weatherstrip.
(7) Install water dam.
(8) Install door trim panel.
(9) Verify operation.
Fig. 18 Power Regulator
1 - SCREW
2 - SCREW
3 - POWER WINDOW REGULATOR
Fig. 19 Power Regulator Bolts
1 - REMOVE BOLTS
2 - LOOSEN BOLTS
3 - DOOR INNER PANEL
23 - 70
DOOR - FRONT
AN
DOORS - REAR
TABLE OF CONTENTS
page
page
DOORS - REAR
DOOR GLASS
REAR DOOR OUTSIDE HANDLE
REAR DOOR GLASS RUN CHANNELS
REAR DOOR HINGE
REAR DOOR INSIDE HANDLE ACTUATOR
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
REAR DOOR LATCH
REAR DOOR LATCH STRIKER
REAR DOOR TRIM PANEL
REAR DOOR WATERDAM
REAR DOOR WINDOW REGULATOR
DOORS - REAR
REMOVAL
(1) Remove B-pillar trim.
(2) Disconnect door wire harness connector.
(3) Support door on suitable stand.
(4) Using a wax crayon or equivalent, mark hinge
position on B-pillar.
(5) Remove
bolts
attaching
hinge
to
B-pillar
(Fig. 1).
INSTALLATION
(1) Align and position door on vehicle.
(2) Install bolts attaching hinge to B-pillar (Fig. 1).
Tighten bolts to 28 N·m (20 ft. lbs.) torque.
(3) Connect door wire harness connector.
(4) Install B-pillar trim.
ADJUSTMENTS
Minor adjustment for alignment of the door is
made by moving the latch striker
IN AND OUT
(1) Loosen the latch striker.
(2) Tap the latch striker inward if the door charac-
ter line is outboard of the body character line or tap
the latch striker outward if the door character line is
inboard of the body character line.
(3) Inspect alignment. If correct, tighten striker to
28 N·m (20 ft. lbs.) torque.
UP AND DOWN
(1) Loosen the latch striker.
(2) Tap the latch striker downward if the door
character line is higher than the body character line
Fig. 1 Rear Door Hinge
1 - B-PILLAR
2 - LOWER HINGE
3 - UPPER HINGE
AN
DOORS - REAR
23 - 71
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст