Dodge Viper SRT-10 (ZB). Manual — part 188
(6) Install the headlamp washer nozzle covers
(Refer to 8 - ELECTRICAL/WIPERS/WASHERS/
WASHER NOZZLE - INSTALLATION).
FRONT BUMPER
REINFORCEMENT
REMOVAL
(1) Remove the fascia. (Refer to 13 - FRAME &
BUMPERS/BUMPERS/FRONT
FASCIA
-
REMOVAL)
(2) Remove the bolts and remove the hood release
handle. (Fig. 5)
(3) Remove the nuts and remove the reinforce-
ment. (Fig. 2)
INSTALLATION
(1) Install the reinforcement and install the nuts.
(2) Tighten the nuts to 54 N·m (40 ft. lbs.).
(3) Install the hood release handle and install the
bolts.
(4) Install the front fascia. (Refer to 13 - FRAME
& BUMPERS/BUMPERS/FRONT FASCIA - INSTAL-
LATION)
Fig. 4 FRONT FASCIA
1 - PUSH ON SPRING NUT
2 - FRAME ASSEMBLY
3 - RIVET NUT
4 - NUT
5 - BOLTS
6 - BUMPER REINFORCEMENT
7 - FRONT FASCIA
8 - FRONT BUMPER
9 - SQUARE NECK BOLT
Fig. 5 HOOD LATCH RELEASE HANDLE
1 - HOOD REMOTE RELEASE ASSEMBLY
2 - FRONT BUMPER REINFORCEMENT
13 - 4
FRAME & BUMPERS
ZB
FRONT FASCIA - EXPORT (Continued)
FRONT BUMPER
REINFORCEMENT - EXPORT
REMOVAL - EXPORT
(1) Remove the fascia (Refer to 13 - FRAME &
BUMPERS/BUMPERS/FRONT
FASCIA
-
REMOVAL).
(2) Remove the bolts and remove the hood release
handle. (Fig. 6)
(3) Disconnect the headlamp washer main hose
from the lower washer reservoir (Fig. 7).
(4) Remove the nuts and remove the reinforce-
ment.
INSTALLATION - EXPORT
NOTE: If installing a new bumper reinforcement,
use the supplied template to cut the holes for the
headlamp washer nozzles.
(1) Install the reinforcement and install the nuts.
(2) Tighten the nuts to 54 N·m (40 ft. lbs.).
(3) Connect the headlamp washer main hose to the
lower washer reservoir.
(4) Install the hood release handle and install the
bolts.
(5) Install the front fascia (Refer to 13 - FRAME &
BUMPERS/BUMPERS/FRONT FASCIA - INSTAL-
LATION).
REAR FASCIA
REMOVAL
(1) Remove the rear wheelhouse splash shields.
(Refer to 23 - BODY/EXTERIOR/REAR WHEEL-
HOUSE SPLASH SHIELD - REMOVAL)
(2) Remove the tail lamp units and position aside.
Refer to the LAMPS/LIGHTING - EXTERIOR of the
service manual.
(3) Remove the nuts attaching fascia to the rear
quarter. (Fig. 8)
(4) Remove the lower fascia screws.
(5) Remove the upper fascia push pin fasteners.
(Fig. 9)
(6) Remove the fascia and disconnect the turn sig-
nal lamp electrical connectors.
(7) Remove the clips and remove the turn signal
lamp units. (Fig. 10)
INSTALLATION
(1) Install the turn signal lamp units and install
the clips.
(2) Position the fascia onto the vehicle and connect
the turn signal lamp electrical connector.
(3) Install the six upper fascia push pin fasteners.
(4) Install the lower fascia to belly pan bolts.
(5) Install the nuts attaching the fascia to the rear
quarter panel and tighten to 6 N·m (50 in lbs.).
(6) Install the tail lamp units. Refer to the
LAMPS/LIGHTING - EXTERIOR of the service man-
ual.
Fig. 6 HOOD LATCH RELEASE HANDLE
1 - HOOD REMOTE RELEASE ASSEMBLY
2 - FRONT BUMPER REINFORCEMENT
Fig. 7 WASHER RESERVOIR HOSE
1 - CLAMP
2 - BUMPER REINFORCEMENT
3 - HEADLAMP WASHER MAIN HOSE
ZB
FRAME & BUMPERS
13 - 5
(7) Install the rear wheelhouse splash shields.
(Refer to 23 - BODY/EXTERIOR/REAR WHEEL-
HOUSE SPLASH SHIELD - INSTALLATION)
Fig. 8 REAR FASCIA TO REAR QUARTER PANEL
1 - FASCIA TO REAR QUARTER PANEL NUT
2 - REAR QUARTER PANEL RETAINER
3 - BODY ASSEMBLY
4 - REAR FASCIA
5 - ROUND SPRING NUT
6 - FASCIA RETAINER
Fig. 9 REAR FASCIA
1 - BODY ASSEMBLY
2 - PUSH PIN
3 - REAR FASCIA
Fig. 10 BACK UP & TURN SIGNAL LAMP REMOVAL
1 - BACK UP & TURN SIGNAL LAMP
2 - U-CLIP
3 - REAR FASCIA
13 - 6
FRAME & BUMPERS
ZB
REAR FASCIA (Continued)
REAR BUMPER FOAM
REMOVAL
(1) Remove the rear fascia. (Refer to 13 - FRAME &
BUMPERS/BUMPERS/REAR FASCIA - REMOVAL)
(2) Remove the push pin fasteners and remove the
foam (Fig. 11).
INSTALLATION
(1) Install the foam and install the push pin fas-
teners.
(2) Install the rear fascia. (Refer to 13 - FRAME &
BUMPERS/BUMPERS/REAR FASCIA - INSTALLA-
TION)
REAR BUMPER
REMOVAL
(1) Remove the rear bumper foam. (Refer to 13 -
FRAME & BUMPERS/BUMPERS/REAR BUMPER
FOAM - REMOVAL)
(2) Remove the bumper nuts and remove the
bumper beam. (Fig. 12)
INSTALLATION
(1) Install the bumper beam and install the nuts.
(2) Tighten the nuts to 54 N·m (40 ft. lbs.).
(3) Install the rear bumper foam. (Refer to 13 -
FRAME & BUMPERS/BUMPERS/REAR BUMPER
FOAM - INSTALLATION)
Fig. 12 FASCIA REAR BUMPER
1 - FRAME ASSEMBLY
2 - SQUARE NECK BOLT
3 - ROUND SPRING NUT
4 - BUMPER REINFORCEMENT
5 - NUTS
6 - FASCIA REAR BUMPER
Fig. 11 REAR BUMPER FOAM
1 - BODY ASSEMBLY
2 - PUSH PIN
3 - REAR BUMPER
ZB
FRAME & BUMPERS
13 - 7
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст