Dodge Viper SRT-10 (ZB). Manual — part 236
(5) Install the two screws hidden by the pull han-
dle cover (Fig. 26).
(6) Install the pull handle cover and install the
screw (Fig. 27).
(7) Install the interior release handle screw and
install the trim plug (Fig. 26).
(8) Install the three trim panel screws in the
speaker opening.
(9) Install the speaker.
(10) Install the two push pins at the rear of the
trim panel and one at the front of the trim panel
(Fig. 27). To install the push pin fastener, first push
the center pin back through the push pin to the open
position. Next install push pin fastener into the open-
ing and push the center pin in flush with the head of
the push pin to the lock position (Fig. 28).
(11) Connect the battery.
Fig. 22 SPRING CLIPS
1 - SPRING CLIPS
2 - DOOR TRIM PANEL
Fig. 23 INSIDE RELEASE HANDLE CABLE
1 - RELEASE HANDLE CABLE
2 - CABLE GROMMET
3 - RELEASE HANDLE ASSEMBLY
4 - FLAT BLADED TOOL (OR EQUIVALENT)
Fig. 24 INSIDE RELEASE HANDLE CABLE
1 - RELEASE HANDLE CABLE
2 - CABLE GROMMET
3 - RELEASE HANDLE ASSEMBLY
4 - FLAT BLADED TOOL (OR EQUIVALENT)
Fig. 25 SPRING CLIPS
1 - SPRING CLIPS
2 - DOOR TRIM PANEL
23 - 36
DOOR - FRONT
ZB
TRIM PANEL (Continued)
WINDOW REGULATOR
REMOVAL
(1) Remove the door glass. (Refer to 23 - BODY/
DOOR - FRONT/DOOR GLASS - REMOVAL)
(2) Disconnect the regulator electrical connector.
(Fig. 29)
(3) Remove the regulator nuts and remove the reg-
ulator.
Fig. 26 DOOR TRIM PANEL
1 - DOOR ASSEMBLY
2 - SPRING NUT
3 - DOOR TRIM PANEL
4 - TRIM PLUG SCREW CAP
5 - SCREW
Fig. 27 DOOR TRIM HANDLE APPLIQUE
1 - DOOR ASSEMBLY
2 - DOOR TRIM PANEL
3 - PUSH PIN FASTENER
4 - HANDLE SCREW
5 - DOOR TRIM HANDLE COVER
Fig. 28 PUSH PIN FASTENER
1 - OPEN POSITION
2 - LOCK POSITION
3 - RELEASE POSITION
Fig. 29 WINDOW REGULATOR
1 - POWER WINDOW REGULATOR
2 - DOOR ASSEMBLY
3 - WIRE HARNESS
ZB
DOOR - FRONT
23 - 37
TRIM PANEL (Continued)
INSTALLATION
(1) Install the regulator and install the nuts.
(2) Tighten the nuts to 12 N·m (9 ft. lbs.).
(3) Connect the electrical connector.
(4) Install the door glass. (Refer to 23 - BODY/
DOOR - FRONT/DOOR GLASS - INSTALLATION)
HINGE COVER - EXPORT
REMOVAL
(1) Remove the side repeater lamp (Refer to 8 -
ELECTRICAL/LAMPS/LIGHTING - EXTERIOR/RE-
PEATER LAMP - REMOVAL).
(2) Remove the 3 screws and the hinge cover (Fig.
30).
INSTALLATION
(1) Cut a hole for the side repeater lamp using the
supplied template.
(2) Position the hinge cover and install the screws.
(3) Install the side repeater lamp (Refer to 8 -
ELECTRICAL/LAMPS/LIGHTING - EXTERIOR/RE-
PEATER LAMP - INSTALLATION).
Fig. 30 HINGE COVER
1 - SIDE REPEATER LAMP
2 - SCREWS
3 - HINGE COVER
23 - 38
DOOR - FRONT
ZB
WINDOW REGULATOR (Continued)
EXTERIOR
TABLE OF CONTENTS
page
page
BELLY PAN
. . . . . . . . . . . . . . . . . . . . . . . . . . . 39
REMOVAL - FRONT EXTENSION BELLY
PAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
REMOVAL - REAR EXTENSION BELLY PAN
INSTALLATION - FRONT EXTENSION BELLY
PAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
INSTALLATION - REAR EXTENSION BELLY
PAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
COWL SCREEN PANEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
. . . . . . . . . . . . . . . . . . . . . . . . . 41
FUEL FILL DOOR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
. . . . . . . . . . . . . . . . . . . . . . . . . 42
FUEL FILLER HOUSING
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
. . . . . . . . . . . . . . . . . . . . . . . . . 42
FRONT WHEELHOUSE SPLASH SHIELD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
. . . . . . . . . . . . . . . . . . . . . . . . . 43
REAR QUARTER PANEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
. . . . . . . . . . . . . . . . . . . . . . . . . 43
REAR WHEELHOUSE SPLASH SHIELD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
. . . . . . . . . . . . . . . . . . . . . . . . . 46
SILL PANEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
. . . . . . . . . . . . . . . . . . . . . . . . . 47
SILL PANEL - EXPORT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
. . . . . . . . . . . . . . . . . . . . . . . . . 48
SIDE VIEW MIRROR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
. . . . . . . . . . . . . . . . . . . . . . . . . 50
GLASS-OUTSIDE REARVIEW MIRROR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
. . . . . . . . . . . . . . . . . . . . . . . . . 50
TRUNK PAN
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
. . . . . . . . . . . . . . . . . . . . . . . . . 51
FRONT FENDER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
. . . . . . . . . . . . . . . . . . . . . . . . . 54
FRONT FENDER - EXPORT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
. . . . . . . . . . . . . . . . . . . . . . . . . 56
FRONT STRUT TOWER TO TOWER BRACE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
. . . . . . . . . . . . . . . . . . . . . . . . . 57
BELLY PAN
REMOVAL
REMOVAL
(1) Raise
and
support
the
vehicle.
(Refer
to
LUBRICATION
&
MAINTENANCE/HOISTING
-
STANDARD PROCEDURE)
(2) Remove the four bolts attaching the belly pan
to the exhaust shield. (Fig. 1)
(3) Remove the bolts and remove the belly pan.
(Fig. 2)
REMOVAL - FRONT EXTENSION BELLY PAN
(1) Raise
and
support
the
vehicle.
(Refer
to
LUBRICATION
&
MAINTENANCE/HOISTING
-
STANDARD PROCEDURE)
(2) Remove the bolts and remove the pan. (Fig. 3)
Fig. 1 BELLY PAN HEAT SHIELD
1 - BELLY PAN
2 - HEAT SHIELD BOLTS (4)
3 - HEAT SHIELD
ZB
EXTERIOR
23 - 39
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст