Dodge Viper SRT-10 (ZB). Manual — part 80
MULTI-FUNCTION SWITCH CONTINUITY TEST
SWITCH POSITION
MODE
CONTINUITY BETWEEN
TURN SIGNAL IN NEUTRAL
HAZARD WARNING SWITCH OFF
HAZARD OFF
B-1 AND B-4
B-1 AND B-5
B-18 AND B-19
B-4 AND B-5
TURN SIGNAL ON
HAZARD WARNING SWITCH OFF
LEFT TURN
A-2 AND B-2
A-2 AND B-4
B-1 AND B-5
B-2 AND B-4
RIGHT TURN
A-2 AND B-5
B-1 AND B-4
B-5 AND B-6
TURN SIGNAL IN NEUTRAL
HAZARD WARNING SWITCH ON
HAZARD ON
A-2 AND B-2
A-2 AND B-4
A-2 AND B-5
A-2 AND B-6
A-3 AND A-5
A-3 AND B-7
B-2 AND B-4
B-2 AND B-5
B-2 AND B-6
B-4 AND B-5
B-4 AND B-6
B-5 AND B-6
HEADLAMP BEAM
LOW
B-16 AND B-18
B-16 AND B-19
B-9 AND B-20
B-1 AND B-4
HIGH
B-17 AND B-18
B-17 AND B-19
B-9 AND B-20
B-1 AND B-4
OPTICAL HORN
ON
B-17 AND B-18
B-17 AND B-19
8L - 28
LAMPS
ZB
MULTI-FUNCTION SWITCH - EXPORT (Continued)
SWITCH POSITION
MODE
CONTINUITY BETWEEN
FRONT FOG
ON
B-13 AND B-14
B-9 AND B-20
B-16 AND B-18
B-16 AND B-19
REAR FOG
B-13 AND B-14
B-9 AND B-20
ON
B-16 AND B-18
B-16 AND B-19
B-18 AND B-19
B-12 AND B-13
MULTI-FUNCTION SWITCH DIMMER CONTROL RESISTANCE
SWITCH POSITION
RESISTANCE VALUE BETWEEN PINS 7 AND 8
DOME ON
150 OHMS
PARADE MODE
411 OHMS
DIM 6 (BRIGHTEST INTENSITY)
768 OHMS
DIM 5
1221 OHMS
DIM 4
1825 OHMS
DIM 3
2593 OHMS
DIM 2
3793 OHMS
DIM 1 (DIMMEST INTENSITY)
5653 OHMS
DEFEAT
8813 OHMS
ZB
LAMPS
8L - 29
MULTI-FUNCTION SWITCH - EXPORT (Continued)
REMOVAL
(1) Open deck lid.
(2) Remove four bolts to battery compartment
cover and remove cover.
(3) Disconnect and isolate the battery negative
cable.
(4) Remove both upper and lower steering column
shrouds.
(5) Disconnect both posi-lock harness connectors at
the rear of the multi-function switch (Fig. 25) and
(Fig. 26).
(6) Remove multi-function switch mounting screws
(Fig. 25) and (Fig. 26).
(7) The windshield wiper/washer switch must be
transferred to the new multi-function switch. (Refer
to 8 - ELECTRICAL/WIPERS/WASHERS/WIPER/
WASHER SWITCH - REMOVAL).
INSTALLATION
(1) The windshield wiper/washer switch must be
transferred to the new multi-function switch. (Refer
Fig. 25 MULTI-FUNCTION SWITCH MOUNTING
1 - MULTI-FUNCTION SWITCH CONNECTOR
2 - HAZARD/WARNING SWITCH
3 - WINDSHIELD WIPER/WASHER SWITCH CONNECTOR
4 - MOUNTING SCREWS
5 - COMBINATION FLASHER
Fig. 26 MULTI-FUNCTION SWITCH - REMOVE/INSTALL
1 - MULTI-FUNCTION SWITCH CONNECTORS
3 - MULTI-FUNCTION SWITCH
2 - RETAINING SCREWS
8L - 30
LAMPS
ZB
MULTI-FUNCTION SWITCH - EXPORT (Continued)
to 8 - ELECTRICAL/WIPERS/WASHERS/WIPER/
WASHER SWITCH - INSTALLATION).
(2) Install the multi-function switch mounting
screws. Tighten multi-function switch to column
retaining screws to 3 N·m (27 in. lbs.) torque.
(3) Connect both posi-lock harness connectors at
the rear of the multi-function switch.
(4) Instal both upper and lower steering column
shrouds.
(5) Connect the battery negative cable.
(6) Place battery access cover into place and install
four bolts.
(7) Close deck lid.
(8) Verify vehicle and system operation.
FRONT SIDE MARKER LAMP
REMOVAL
(1) Open deck lid.
(2) Remove four bolts to battery compartment
cover and remove cover.
(3) Disconnect and isolate the battery negative
cable.
(4) Remove front fender extension splash shield on
the respective side by removing the fasteners (Fig.
14).
(5) Remove the front side marker lamp by turning
1/4 turn counterclockwise and pulling straight out.
(6) Pull the lamp straight out of the lamp socket
and remove from vehicle.
INSTALLATION
(1) Place marker lamp into socket and install in
rear of headlamp unit. turn 1/4 turn clockwise until
stops.
(2) Install the front fender extension splash shield
on the respective side by and the fasteners (Fig. 14).
(3) Connect the battery negative cable.
(4) Place battery access cover into place and install
four bolts.
(5) Close deck lid.
(6) Verify vehicle and system operation.
REAR SIDE MARKER LAMP
REMOVAL
It is not necessary to remove the tail lamp unit to
change lamps.
(1) Open deck lid.
(2) Remove four bolts to battery compartment
cover and remove cover.
(3) Disconnect and isolate the battery negative
cable.
(4) Remove the two Torx head retaining screws to
the access panel of the respective side of the vehicle
and remove panel.
(5) Reach in behind the tail lamp unit and turn
the respective bulb counterclockwise, pull forward
and remove.
INSTALLATION
It is not necessary to remove the tail lamp unit to
change lamps.
(1) Reach in behind the tail lamp unit and place
lamp in socket, put in lamp unit opening and turn
the lamp socket clockwise until it locks into place.
(2) Install the two Torx head retaining screws to
the access panel of the respective side of the vehicle.
(3) Connect the battery negative cable.
(4) Place battery access cover into place and install
four bolts.
(5) Close deck lid.
(6) Verify vehicle and system operation.
REPEATER LAMP - EXPORT
REMOVAL
(1) Open the door and reach through the door jam,
depress the side repeater lamp retaining tabs and
release from the hinge cover (Fig. 27).
(2) Pull side repeater lamp out and disengage bulb
socket from lamp.
(3) Rotate and pull the bulb from the socket.
Fig. 27 SIDE REPEATER LAMP
1 - SIDE REPEATER LAMP
2 - HINGE COVER
ZB
LAMPS
8L - 31
MULTI-FUNCTION SWITCH - EXPORT (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст