Lifan 620. Manual — part 15
27. DTC: P0508, Idle Speed Regulator Control Circuit Voltage Too Low (see Table 1-40)
Table 1-40
S/N Operation Test
Results
Actions
1
Connect the diagnostic instrument and adapter, and turn the
ignition switch to ON.
Next
step
Yes Next
step
2
Disconnect the idle speed regulator. Check the resistance
between pin A and pin D, as well as between pin B and pin C
3
1
2
3
1
ignition switch to ON.
Yes Next
step
2
Disconnect the idle speed regulator. Check the resistance
between pin A and pin D, as well as between pin B and pin C
of the regulator. Is the resistance about 53±5.3Ω under the
temperature of 20 ?
℃
No
Replace stepper motor
Yes
Repair or replace
harness
3
Check for open circuit between the pin A, B, C, D of the
regulator and the pin 65#, 66#, 67#, 64# of the ECU.
No
Diagnosis help
61
30. DTC: P0560, System Voltage Signal Abnormal (see Table 1-43)
Table 1-43
S/N Operation Test
Results
Actions
1
Connect the diagnostic instrument and adapter, and turn the
ignition switch to OFF.
Next
step
Yes Next
step
2
Check the volatage with a multimeter. Is the voltage about
12V?
3
4
5
1
2
3
ECU and the pin 87# of the main relay repectively. Is the
resistance too high?
No Next
step
Yes Next
step
4
Start the engine, check if the generator charging voltage is
within 9-16V under different rotation speed.
No Replace
engine
Yes Diagnosis
help
5
Check the grounding point of the engine harness for normal
operation.
No
Repair or replace
harness
62
32. DTC: P0601, Electronic Control Unit Check Code Unprogrammed (see Table 1-45)
Table 1-45
S/N Operation Test
Results
Actions
1
Connect the diagnostic instrument and adapter, and turn the
ignition switch to ON.
Next
step
Yes Next
step
2
Clear the DTC, and check once again if the trouble is stable.
No Normal
3 Replace
ECU.
End
1
2
3
1
2
3
end of the relay.
No
Go to step 2
Yes Replace
relay
4
Measure the voltage between the pin 86# of the relay
(control end) and the power supply negative pole with a
multimeter. Is the voltage about 3.7V?
No Next
step
Yes
Repair or replace
harness
5
Check for open circuit between the pin 86# of the relay
(control end) and the 70# of the ECU with a multimeter.
No Diagnosis
help
63
35. DTC: P0646, A/C Compressor Relay Control Circuit Voltage Too Low (see Table 1-48)
Table 1-48
S/N Operation Test
Results
Actions
1
Connect the diagnostic instrument and adapter, and turn the
ignition switch to OFF.
Next
step
Yes
Go to step 4
2
Disconnect the A/C compressor relay, and turn the ignition
switch to ON. Measure the voltage between pin 30#, 85# of
the relay (power supply end) and the power supply negative
3
4
5
1
2
3
No
Go to step 2
Yes Replace
relay
4
Measure the voltage between the pin 86# of the relay
(control end) and the power supply negative pole with a
multimeter. Is the voltage about 3.7V?
No Next
step
Yes
Repair or replace
harness
5
Check for short to power supply between the pin 86# of the
relay (control end) and the 70# of the ECU with a multimeter.
No Diagnosis
help
64
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст