Infiniti M35/M45 Y50. Manual — part 85
ON-VEHICLE SERVICE
AT-263
D
E
F
G
H
I
J
K
L
M
A
B
AT
Revolution Sensor Components (2WD Models Only)
NCS001QW
REMOVAL AND INSTALLATION
Components
VQ35DE models
SCIA8043E
1.
Rear extension
2.
A/T
3.
Oil pan gasket
4.
Clip
5.
Oil pan mounting bolt
6.
Oil pan
7.
Drain plug
8.
Drain plug gasket
9.
Revolution sensor
10.
Self-sealing bolt
Refer to GI section to make sure icons (symbol marks) in the figure. Refer to
.
However, refer to the following symbols for others.
*
:
Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to
GI-47, "Recommended Chemical Products and Sealants"
.
AT-264
ON-VEHICLE SERVICE
VK45DE models
Removal
1.
Disconnect the battery cable from the negative terminal.
2.
Drain ATF through drain plug.
3.
Remove exhaust front tube and center muffler with power tool. Refer to
EX-5, "Removal and Installation"
4.
Remove rear propeller shaft. Refer to
PR-8, "Removal and Installation"
5.
Remove control rod. Refer to
AT-226, "Control Rod Removal and Installation"
.
6.
Remove oil pan, oil pan gasket and clips (VQ35DE models) or oil pan, oil pan gasket, brackets and clips
(VK45DE models) according to the following procedures.
a.
VQ35DE models
SCIA8047E
1.
Output shaft & companion flange complement
2.
A/T
3.
Oil pan gasket
4.
Clip
5.
Bracket
6.
Bracket
7.
Oil pan mounting bolt
8.
Oil pan
9.
Drain plug
10.
Drain plug gasket
11.
Revolution sensor
12.
Self-sealing bolt
Refer to GI section to make sure icons (symbol marks) in the figure. Refer to
However, refer to the following symbols for others.
*
:
Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to
GI-47, "Recommended Chemical Products and Sealants"
.
ON-VEHICLE SERVICE
AT-265
D
E
F
G
H
I
J
K
L
M
A
B
AT
i.
Remove clips (1).
ii.
Remove oil pan (2) and oil pan gasket.
: Front
: Bolt (22)
b.
VK45DE models
i.
Remove clips (1) and brackets (2).
ii.
Remove oil pan (3) and oil pan gasket.
: Front
: Bolt (22)
7.
Check foreign materials in oil pan to help determine causes of
malfunction. If the ATF is very dark, smells burned, or contains
foreign particles, the frictional material (clutches, band) may
need replacement. A tacky film that will not wipe clean indicates
varnish build up. Varnish can cause valves, servo, and clutches
to stick and can inhibit pump pressure.
●
If frictional material is detected, perform A/T fluid cooler
cleaning. Refer to
AT-14, "A/T Fluid Cooler Cleaning"
.
8.
Support A/T assembly with a transmission jack.
CAUTION:
When setting transmission jack, place wooden blocks to
prevent from damaging control valve with TCM and trans-
mission case.
9.
Remove rear engine mounting member with power tool. Refer to
AT-274, "Removal and Installation (2WD
10. Remove rear extension assembly (VQ35DE models) or output shaft & companion flange complement
(VK45DE models) according to the following procedures.
a.
VQ35DE models
i.
Remove tightening bolts for rear extension assembly and trans-
mission case.
SCIA8039E
SCIA8035E
SCIA5199E
SCIA6941E
AT-266
ON-VEHICLE SERVICE
ii.
Tap rear extension assembly with a soft hammer.
iii.
Remove rear extension assembly from transmission case. (With
needle bearing.)
b.
VK45DE models
i.
Remove tightening bolts (1) for output shaft & companion flange
complement and transmission case.
: Bolt (10)
●
Self-sealing bolts (2)
ii.
Tap output shaft & companion flange complement with a soft
hammer.
SCIA3432E
SCIA3431E
SCIA6943E
SCIA5687E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст