Infiniti M35/M45 Y50. Manual — part 84
ON-VEHICLE SERVICE
AT-259
D
E
F
G
H
I
J
K
L
M
A
B
AT
13. Remove return spring (1) from parking pawl (2).
Inspection
●
If the contact surface on parking actuator support, parking pawl,
etc. has excessive wear, abrasion, bend, or any other damage,
replace the components.
Installation
CAUTION:
After completing installation, check A/T fluid leakage, A/T fluid level and A/T position. Refer to
AT-228, "Checking of A/T Position"
1.
Install return spring (1) to parking pawl (2).
SCIA6180J
SCIA5143E
SCIA5144E
SCIA6180J
AT-260
ON-VEHICLE SERVICE
2.
Install parking pawl (with return spring) (1) and pawl shaft (2) in
output shaft & companion flange complement.
3.
Install parking actuator support (1) in output shaft & companion
flange complement.
4.
Apply recommended sealant (Genuine Anaerobic Liquid Gasket
or equivalent. Refer to
GI-47, "Recommended Chemical Prod-
.) to output shaft & companion flange com-
plement as shown in the figure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc.
from the transmission case and output shaft & companion
flange complement mounting surfaces.
5.
Install output shaft & companion flange complement to transmis-
sion case.
6.
Tighten output shaft & companion flange complement bolts (1)
to the specified torque. Refer to
: Bolt (10)
CAUTION:
Do not reuse self-sealing bolts (2).
Refer to GI section to make sure icons (symbol marks) in the fig-
ure. Refer to
.
SCIA7066E
SCIA7065E
SCIA5212E
SCIA5688E
SCIA6943E
ON-VEHICLE SERVICE
AT-261
D
E
F
G
H
I
J
K
L
M
A
B
AT
7.
Install engine mounting insulator (rear). Refer to
AT-274, "Removal and Installation (2WD Models)"
8.
Install rear engine mounting member. Refer to
AT-274, "Removal and Installation (2WD Models)"
9.
AT-226, "Control Rod Removal and Installation"
10. Install rear propeller shaft. Refer to
PR-8, "Removal and Installation"
.
11. Install exhaust front tube and center muffler. Refer to
EX-7, "Removal and installation"
12. Install drain plug to oil pan. Tighten a necessary drain plug with specified torque. Refer to
Valve With TCM and A/T Fluid Temperature Sensor 2"
CAUTION:
Do not reuse drain plug gasket.
13. Pour ATF into A/T assembly. Refer to
.
AT-262
ON-VEHICLE SERVICE
Rear Oil Seal (VQ35DE Models Only)
NCS001QV
REMOVAL AND INSTALLATION
Removal
1.
Remove rear propeller shaft. Refer to
2.
Remove transfer assembly from A/T assembly (AWD models).
Refer to
TF-44, "Removal and Installation"
3.
Remove rear oil seal using a flat-bladed screwdriver.
CAUTION:
Be careful not to scratch rear extension assembly (2WD
models) or adapter case assembly (AWD models).
Installation
CAUTION:
After completing installation, check for A/T fluid leakage and A/T fluid level. Refer to
.
1.
As shown in the figure, use the drift to drive rear oil seal into rear
extension assembly (2WD models) or adapter case assembly
(AWD models) until it is flush.
CAUTION:
●
Do not reuse rear oil seal.
●
Apply ATF to rear oil seal.
2.
Install transfer assembly to A/T assembly (AWD models). Refer
to
TF-44, "Removal and Installation"
3.
Install rear propeller shaft. Refer to
.
SCIA5410E
SCIA5411E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст