Infiniti M35/M45 Y50. Manual — part 83
ON-VEHICLE SERVICE
AT-255
D
E
F
G
H
I
J
K
L
M
A
B
AT
5.
Install bearing (1) to rear extension.
CAUTION:
●
Take care with the direction of needle bearing. Refer to
AT-298, "Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
●
Apply petroleum jelly to needle bearing.
Refer to GI section to make sure icons (symbol marks) in the fig-
ure. Refer to
6.
Install seal rings to output shaft.
CAUTION:
●
Do not reuse seal rings.
●
Apply petroleum jelly to seal rings.
7.
Install parking gear to output shaft
8.
Install output shaft in transmission case.
9.
Install bearing race to output shaft.
SCIA6179J
SCIA5209E
SCIA5247E
SCIA5246E
SCIA5245E
AT-256
ON-VEHICLE SERVICE
10. Apply recommended sealant (Genuine Anaerobic Liquid Gasket
GI-47, "Recommended Chemical Prod-
.) to rear extension assembly as shown in
the figure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc.
from the transmission case and rear extension assembly
mounting surfaces.
11. Install rear extension assembly to transmission case. (With nee-
dle bearing.)
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.
12. Tighten rear extension assembly bolts to the specified torque.
Refer to
CAUTION:
Do not reuse self-sealing bolts.
13. Install engine mounting insulator (rear). Refer to
AT-274, "Removal and Installation (2WD Models)"
.
14. Install rear engine mounting member. Refer to
AT-274, "Removal and Installation (2WD Models)"
15. Install control rod. Refer to
AT-226, "Control Rod Removal and Installation"
.
16. Install rear propeller shaft. Refer to
PR-8, "Removal and Installation"
17. Install exhaust front tube and center muffler. Refer to
EX-5, "Removal and Installation"
18. Install drain plug to oil pan. Tighten a necessary drain plug with specified torque. Refer to
Valve With TCM and A/T Fluid Temperature Sensor 2"
CAUTION:
Do not reuse drain plug gasket.
19. Pour ATF into A/T assembly. Refer to
SCIA5212E
SCIA3431E
SCIA6941E
ON-VEHICLE SERVICE
AT-257
D
E
F
G
H
I
J
K
L
M
A
B
AT
REMOVAL AND INSTALLATION (VK45DE MODELS)
Components
Removal
1.
Drain ATF through drain plug.
2.
Remove exhaust front tube and center muffler with a power tool. Refer to
EX-7, "Removal and installation"
.
3.
Remove rear propeller shaft. Refer to
PR-8, "Removal and Installation"
.
4.
Remove control rod. Refer to
AT-226, "Control Rod Removal and Installation"
5.
Support A/T assembly with a transmission jack.
CAUTION:
When setting transmission jack, be careful not to allow it to collide against the drain plug.
6.
Remove rear engine mounting member with a power tool. Refer to
AT-274, "Removal and Installation
.
7.
Remove engine mounting insulator (rear). Refer to
AT-274, "Removal and Installation (2WD Models)"
.
1.
Output shaft & companion flange complement
2.
Parking actuator support
3.
Return spring
4.
Parking pawl
5.
Pawl shaft
6.
Self-sealing bolt
Refer to GI section to make sure icons (symbol marks) in the figure. Refer to
.
However, refer to the following symbols for others.
*
:
Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to
GI-47, "Recommended Chemical Products and Sealants"
.
SCIA7029E
AT-258
ON-VEHICLE SERVICE
8.
Remove tightening bolts (1) for output shaft & companion flange
complement and transmission case.
: Bolt (10)
●
Self-sealing bolts (2)
9.
Tap output shaft & companion flange complement with a soft
hammer.
10. Remove output shaft & companion flange complement from
transmission case.
11. Remove parking actuator support (1) from output shaft & com-
panion flange complement.
12. Remove parking pawl (with return spring) (1) and pawl shaft (2)
from output shaft & companion flange complement.
SCIA6943E
SCIA5687E
SCIA5688E
SCIA7065E
SCIA7066E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст