Infiniti M35/M45 Y50. Manual — part 81
ON-VEHICLE SERVICE
AT-247
D
E
F
G
H
I
J
K
L
M
A
B
AT
7.
Straighten terminal clip to free A/T fluid temperature sensor 2
harness.
8.
Remove A/T fluid temperature sensor 2 with bracket from con-
trol valve with TCM.
9.
Remove bracket from A/T fluid temperature sensor 2.
Installation
CAUTION:
After completing installation, check for A/T fluid leakage and A/T fluid level. Refer to
1.
Install A/T fluid temperature sensor 2 to bracket.
SCIA5146E
SCIA5253E
SCIA5264E
SCIA5264E
AT-248
ON-VEHICLE SERVICE
2.
Install A/T fluid temperature sensor 2 (with bracket) in control
valve with TCM. Tighten A/T fluid temperature sensor 2 bolts to
the specified torque. Refer to
.
3.
Connect A/T fluid temperature sensor 2 connector.
4.
Securely fasten A/T fluid temperature sensor 2 harness with ter-
minal clip.
5.
Install oil pan, oil pan gasket and clips (VQ35DE models) or oil pan, oil pan gasket, brackets and clips
(VK45DE models) according to the following procedures.
a.
VQ35DE models
i.
Install oil pan gasket to oil pan.
CAUTION:
●
Do not reuse oil pan gasket.
●
Install it in the direction to align hole positions.
●
Complete remove all moisture, oil and old gasket, etc. from oil pan gasket mounting surface.
ii.
Install oil pan (2) (with oil pan gasket) and clips (1) to transmis-
sion case.
: Front
: Bolt (22)
CAUTION:
●
Install it so that drain plug comes to the position as
shown in the figure.
●
Be careful not to pinch harnesses.
●
Completely remove all moisture, oil and old gasket, etc.
from oil pan mounting surface.
SCIA5253E
SCIA5023E
SCIA5146E
SCIA8039E
ON-VEHICLE SERVICE
AT-249
D
E
F
G
H
I
J
K
L
M
A
B
AT
iii.
Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
Tighten oil pan mounting bolts to the specified torque. Refer to
.
CAUTION:
Do not reuse oil pan mounting bolts.
b.
VK45DE models
i.
Install oil pan gasket to oil pan.
CAUTION:
●
Do not reuse oil pan gasket.
●
Install it in the direction to align hole positions.
●
Complete remove all moisture, oil and old gasket, etc. from oil pan gasket mounting surface.
ii.
Install oil pan (3) (with oil pan gasket), clips (1) and brackets (2)
to transmission case.
: Front
: Bolt (22)
CAUTION:
●
Install it so that drain plug comes to the position as
shown in the figure.
●
Be careful not to pinch harnesses.
●
Completely remove all moisture, oil and old gasket, etc.
from oil pan mounting surface.
●
Be careful with installation direction of brackets (2).
iii.
Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
Tighten oil pan mounting bolts to the specified torque. Refer to
.
CAUTION:
Do not reuse oil pan mounting bolts.
6.
Install drain plug to oil pan. Tighten drain plug to the specified
torque. Refer to
CAUTION:
Do not reuse drain plug gasket.
7.
Connect heated oxygen sensor 2 harness connector.
8.
Pour ATF into A/T assembly. Refer to
.
9.
Connect the battery cable to the negative terminal.
SCIA4113E
SCIA8035E
SCIA4113E
AT-250
ON-VEHICLE SERVICE
Parking Components (2WD Models Only)
NCS001QU
REMOVAL AND INSTALLATION (VQ35DE MODELS)
Components
Removal
1.
Drain ATF through drain plug.
2.
Remove exhaust front tube and center muffler with power tool. Refer to
EX-5, "Removal and Installation"
.
3.
Remove rear propeller shaft. Refer to
PR-8, "Removal and Installation"
4.
Remove control rod. Refer to
AT-226, "Control Rod Removal and Installation"
.
5.
Support A/T assembly with a transmission jack.
CAUTION:
When setting transmission jack, be careful not to allow it to collide against the drain plug.
6.
Remove rear engine mounting member with power tool. Refer to
AT-274, "Removal and Installation (2WD
.
7.
Remove engine mounting insulator (rear). Refer to
AT-274, "Removal and Installation (2WD Models)"
.
1.
Rear oil seal
2.
Rear extension
3.
Parking actuator support
4.
Return spring
5.
Parking pawl
6.
Pawl shaft
7.
Self-sealing bolt
8.
Seal ring
9.
Parking gear
10.
Output shaft
11.
Bearing race
12. Needle bearing
Refer to GI section to make sure icons (symbol marks) in the figure. Refer to
However, refer to the following symbols for others.
*
:
Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to
GI-47, "Recommended Chemical Products and Sealants"
.
SCIA7030E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст