Infiniti FX35 / FX45. Manual — part 216
DOOR
BL-131
< SERVICE INFORMATION >
C
D
E
F
G
H
J
K
L
M
A
B
BL
N
O
P
DOOR
Fitting Adjustment
INFOID:0000000001327873
FRONT DOOR
Longitudinal Clearance and Surface Height Adjustment at Front End.
Loosen the hinge mounting bolts. Raise the front door at rear end to adjust.
REAR DOOR
Longitudinal Clearance and Surface Height Adjustment at Front End.
1.
Remove the center pillar upper garnish and center pillar lower garnish. Refer to
2.
Accessing from inside the vehicle, loosen the mounting nuts. Open the rear door, and raise the rear door
at rear end to adjust.
STRIKER ADJUSTMENT
1.
Front fender
2.
Front door outer
3.
Rear door outer
4.
Bolt 5.
Nut
PIIA6059E
BL-132
< SERVICE INFORMATION >
DOOR
Adjust the striker so that it becomes parallel with the lock insertion
direction.
Removal and Installation of Front Door
INFOID:0000000001327874
CAUTION:
• When removing and installing the front door assembly, support the door with a jack and cloth to pro-
tect the door and body.
• When removing and installing front door assembly, be sure to carry out the fitting adjustment Refer
• Check the hinge rotating part for poor lubrication. If necessary, apply “body grease”.
• After installing, apply touch-up paint (the body color) onto the head of the hinge mounting nuts.
• Operate with two workers, because of its heavy weight.
• After installing, check operation.
REMOVAL
1.
Pull the lever and remove the front door harness connector
while removing tabs of door harness connector.
2.
Remove the mounting bolts of the check link on the vehicle.
3.
Remove the door-side hinge mounting nuts, and remove the
door assembly.
: 16.7 N·m (1.7 kg-m, 12.4 ft-lb)
PIIB2804J
PIIA2514E
PIIA6020E
PIIA6021E
DOOR
BL-133
< SERVICE INFORMATION >
C
D
E
F
G
H
J
K
L
M
A
B
BL
N
O
P
INSTALLATION
Install in the reverse order of removal.
Removal and Installation of Rear Door
INFOID:0000000001327875
CAUTION:
• When removing and installing the rear door assembly, support the door with a jack and cloth to pro-
tect the door and body.
• When removing and installing rear door assembly, be sure to carry out the fitting adjustment Refer
• After installing, apply touch-up paint (the body color) onto the head of the hinge mounting nuts.
• Operate with two workers, because of its heavy weight.
• Check the hinge rotating part for poor lubrication. If necessary, apply “body grease”.
• After installing, check operation.
REMOVAL
1.
Grommet is pulled out, and the Rear door harness connector is
detached.
2.
Remove the mounting bolts of the check link on the vehicle.
3.
Remove the door-side hinge mounting nuts, and remove the
door assembly.
INSTALLATION
Install in the reverse order of removal.
PIIA2787E
PIIA6022E
PIIA6023E
BL-134
< SERVICE INFORMATION >
DOOR
Removal and Installation of Door Weatherstrip
INFOID:0000000001327876
REMOVAL
1.
Remove the mounting bolts of the check link on the vehicle. Refer to
BL-132, "Removal and Installation of
BL-133, "Removal and Installation of Rear Door"
2.
Remove the weatherstrip clips and remove weatherstrip.
INSTALLATION
Install in the reverse order of removal.
1.
Weatherstrip
2.
Clip
PIIA6024E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст