Infiniti FX35 / FX45. Manual — part 832
MA-8
< SERVICE INFORMATION >
PERIODIC MAINTENANCE
NOTE:
(1) After 60,000 miles (96,000 km) or 48 months, inspect every 15,000 miles (24,000 km) or 12 months. Replace the drive belts if found
damaged or if the auto belt tensioner reading (only for VK45DE engine) reaches the maximum limit.
(2) Maintenance-free item. For service procedures, refer to FL section.
(3) After 60,000 miles (96,000 km) or 48 months, replace every 30,000 miles (48,000 km) or 24 months.
(4) If valve noise increases, inspect valve clearance.
* Maintenance items and intervals with “*” are recommended by INFINITI for reliable vehicle operation. The owner need not perform
such maintenance in order to maintain the emission warranty or manufacturer recall liability. Other maintenance items and intervals are
required
CHASSIS AND BODY MAINTENANCE
Abbreviations: R = Replace.
I = Inspect. Correct or replace if necessary.
NOTE:
(1) Using automatic transmission fluid other than Genuine NISSAN Matic J ATF will cause deterioration in driveability and
automatic transmission durability, and may damage the automatic transmission, which is not covered by the INFINITI new
vehicle limited warranty.
(2) Refer to “Tire rotation” under the “GENERAL MAINTENANCE” heading earlier in this section.
Engine coolant
NOTE (3)
R*
Engine oil
R
R
R
R
R
R
R
R
Engine oil filter (Use genuine
NISSAN engine oil filter or equiv-
alent.)
R
R
R
R
R
R
R
R
Spark plugs (PLATINUM-
TIPPED type)
Replace every 105,000 miles (169,000 km).
Intake & exhaust valve clear-
ance*
NOTE (4)
MAINTENANCE OPERATION
MAINTENANCE INTERVAL
Reference Sec-
tion - Page or -
Content Title
Perform at number of miles, kilo-
meters or months, whichever
comes first.
Miles x 1,000
(km x 1,000)
Months
7.5
(12)
6
15
(24)
12
22.5
(36)
18
30
(48)
24
37.5
(60)
30
45
(72)
36
52.5
(84)
42
60
(96)
48
MAINTENANCE OPERATION
MAINTENANCE INTERVAL
Reference Sec-
tion - Page or -
Content Title
Perform at number of miles, kilo-
meters or months, whichever
comes first.
Miles x 1,000
(km x 1,000)
Months
7.5
(12)
6
15
(24)
12
22.5
(36)
18
30
(48)
24
37.5
(60)
30
45
(72)
36
52.5
(84)
42
60
(96)
48
Brake lines & cables
I
I
I
I
Brake pads & rotors
I
I
I
I
Automatic transmission & trans-
fer fluid & differential gear oil
NOTE (1)
I
I
I
I
Steering gear, linkage & transfer
gear, axle & suspension parts
I
I
,
Tire rotation
NOTE (2)
Drive shaft boots and propeller
shaft (AWD models)
I
I
I
I
Exhaust system
I
I
In-cabin microfilter
R
R
R
R
RECOMMENDED FLUIDS AND LUBRICANTS
MA-9
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
K
M
A
B
MA
N
O
P
RECOMMENDED FLUIDS AND LUBRICANTS
Fluids and Lubricants
INFOID:0000000001328897
*1: For further details, see “Engine Oil Recommendation”.
*2: Using automatic transmission fluid other than Genuine NISSAN Matic J ATF will cause deterioration in driveability and
automatic transmission durability, and may damage the automatic transmission, which is not covered by the INFINITI new
vehicle limited warranty.
*3: For hot climates, viscosity SAE 90 is suitable for ambient temperatures above 0
°
C (32
°
F).
*4: Canada NISSAN Automatic Transmission Fluid or DEXRON
TM
VI type ATF may also be used.
*5: Available in mainland U.S.A. through your INFINITI dealer.
Engine Oil Recommendation
INFOID:0000000001328898
NISSAN recommends the use of an energy conserving oil in order to improve fuel economy.
Select only engine oils that meet the American Petroleum Institute (API) certification and International Lubri-
cant Standardization and Approval Committee (ILSAC) certification and SAE viscosity standard. These oils
have the API certification mark on the front of the container. Oils which do not have the specified quality label
should not be used as they could cause engine damage.
Capacity (Approximate)
Recommended Fluids/Lubricants
US measure
Imp mea-
sure
Liter
Engine oil
Drain and
refill
With oil fil-
ter change
VK45DE
6-1/8 qt
5-1/8 qt
5.8
• Engine oil with API Certification Mark*1
• Viscosity SAE 5W-30
VQ35DE
5 qt
4 - 1/8 qt
4.7
Without oil
filter
change
VK45DE
5-1/2 qt
4-5/8 qt
5.2
VQ35DE
4-5/8 qt
3-7/8 qt
4.4
Dry engine (Overhaul)
VK45DE
7-3/8 qt
6-1/8 qt
7.0
VQ35DE
5-3/4 qt
4-3/4 qt
5.4
Cooling
system
With res-
ervoir tank
VK45DE
10-5/8 qt
8-3/4 qt
10.0
Genuine NISSAN Long Life Antifreeze/ Coolant
or equivalent
VQ35DE
9-1/8 qt
7-5/8 qt
8.6
Reservoir
tank
VK45DE
7/8 qt
3/4 qt
0.8
VQ35DE
7/8 qt
3/4 qt
0.8
Automatic transmission fluid
10-7/8 qt
9-1/8 qt
10.3
Genuine NISSAN Matic J ATF *2
Differential gear oil
Front
1-3/8 pt
1-1/8 pt
0.65
Genuine NISSAN Differential Oil Hypoid Super
GL-5 80W-90 or API GL-5, Viscosity SAE 80W-
90 *3
Rear
3 pt
2-1/2 pt
1.40
Transfer fluid
2-5/8 pt
2-1/4 pt
1.25
Genuine NISSAN Matic D ATF (Continental U.S.
and Alaska) or Canada NISSAN Automatic
Transmission Fluid or equivalent (if available)
Power steering fluid (PSF)
1-1/8 qt
7/8 qt
1.0
Genuine NISSAN PSF or equivalent*4
Brake fluid
—
—
—
Genuine NISSAN Super Heavy Duty Brake Flu-
id*5 or equivalent
DOT 3 (US FMVSS No. 116)
Multi-purpose grease
—
—
—
NLGI No. 2 (Lithium soap base)
Windshield washer fluid
—
—
—
Genuine NISSAN Windshield Washer Concen-
trate Cleaner & Antifreeze or equivalent
Fuel
recommendation
VK45DE
—
—
—
Refer to
GI-5, "Precaution for Fuel (Unleaded
VQ35DE
—
—
—
Refer to
MA-10
< SERVICE INFORMATION >
RECOMMENDED FLUIDS AND LUBRICANTS
Anti-Freeze Coolant Mixture Ratio
INFOID:0000000001328899
The engine cooling system is filled at the factory with a high-quality,
year-round, anti-freeze coolant solution. The anti-freeze solution
contains rust and corrosion inhibitors. Therefore, additional cooling
system additives are not necessary.
CAUTION:
When adding or replacing coolant, be sure to use only Genuine
Nissan Long Life Antifreeze/ Coolant or equivalent with the
proper mixture ratio of 50% anti-freeze and 50% demineralized
water/distilled water.
Other types of coolant solutions may damage your cooling sys-
tem.
1.
API certification mark
2.
API service symbol
SAIA1514E
SMA947CA
ENGINE MAINTENANCE (VQ35DE ENGINE)
MA-11
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
K
M
A
B
MA
N
O
P
ENGINE MAINTENANCE (VQ35DE ENGINE)
Checking Drive Belts
INFOID:0000000001328900
WARNING:
Be sure to perform when engine is stopped.
1.
Inspect belts for cracks, fraying, wear and oil. If necessary, replace.
2.
Inspect drive belt deflection or tension at a point on belt midway
between pulleys.
• Inspection should be done only when engine is cold, or over
30 minutes after engine is stopped.
• Measure the belt tension with belt tension gauge (Commercial
service tool: BT3373-F or equivalent) (A) at points marked
shown in the figure.
• When measuring the deflection, apply 98 N (10 kg, 22 lb) at
the marked point.
• Adjust if the belt deflection exceeds the limit or if the belt ten-
sion is not within specifications.
CAUTION:
• When checking the belt deflection or the tension immedi-
ately after installation, first adjust it to the specified value.
Then, after turning crankshaft two turns or more, re-adjust
to the specified value to avoid variation in deflection
between pulleys.
• Tighten idler pulley lock nut by hand and measure the deflection or the tension without loose-
ness.
Belt Deflection and Tension
*: If belt tension gauge cannot be installed at check points shown, check drive belt tension at different location on belt.
Drive Belts Tension Adjustment
INFOID:0000000001328901
CAUTION:
1 : Power steering oil pump
2 : Alternator
3 : Idler pulley
4 : Crankshaft pulley
5 : A/C compressor
JPBIA0421ZZ
JPBIA0422ZZ
Items
Deflection adjustment
Unit: mm (in)
Tension adjustment*
Unit: N (kg, lb)
Used belt
New belt
Used belt
New belt
Limit
After adjustment
Limit
After adjustment
Alternator and
power steering
oil pump belt
12 (0.47)
7 - 8
(0.28 - 0.31)
6 - 7
(0.24 - 0.28)
294 (30, 66)
730 - 818
(74.5 - 83.5,
164 - 184)
838 - 926
(85.5 - 94.5,
188 - 208)
A/C compressor
belt
12 (0.47)
9 - 10
(0.35 - 0.39)
8 - 9
(0.31 - 0.35)
196 (20, 44)
348 - 436
(35.5 - 44.5,
78 - 98)
470 - 559
(48 - 57,
106 - 126)
Applied pushing
force
98 N (10 kg, 22 lb)
—
Portion
Belt tightening method for adjustment
Alternator and power steering oil pump belt
Adjusting bolt on idler pulley
A/C compressor belt
Adjusting bolt on idler pulley
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст