Infiniti FX35 / FX45. Manual — part 817
INTERIOR ROOM LAMP
LT-163
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
M
A
B
LT
N
O
P
1.
Turn ignition switch OFF.
2.
Check voltage between front step lamp (driver side and passen-
ger side) harness connector and ground.
3.
Check voltage between rear step lamp (LH and RH) harness
connector and ground.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 4.
3.
CHECK STEP LAMP CIRCUIT
1.
Disconnect BCM connector and front door driver side step lamp connector.
2.
Check continuity between BCM harness connector and front
step lamp harness connector.
3.
Check continuity between BCM harness connector and rear
step lamp harness connector.
OK or NG
OK
>> Replace BCM if step lamp does not work after setting the connector again. Refer to
"Removal and Installation of BCM"
NG
>> Repair harness or connector.
4.
CHECK STEP LAMP CIRCUIT
1.
Disconnect BCM connector and front door driver side step lamp connector.
Terminals
Voltage
(Approx.)
(+)
(-)
Front step lamp connector
Terminal
Driver side
D9
1
Ground Battery
voltage
Passenger
side
D39
1
Terminals
Voltage
(Approx.)
(+)
(-)
Rear step lamp connector
Terminal
LH
D60
1
Ground Battery
voltage
RH
D80
1
PKIA5264E
BCM
connector
Terminal
Front step lamp
connector
Terminal
Continuity
M4
47
Driver side
D9
2
Yes
Passenger
side
D39
2
BCM
connector
Terminal
Rear step lamp connector
Terminal
Continuity
M4
47
LH
D80
2
Yes
RH
D60
2
PKIB3522E
LT-164
< SERVICE INFORMATION >
INTERIOR ROOM LAMP
2.
Check continuity between BCM harness connector and front
step lamp harness connector.
3.
Check continuity between BCM harness connector and rear
step lamp harness connector.
OK or NG
OK
>> Replace BCM if step lamp does not work after setting the connector again. Refer to
"Removal and Installation of BCM"
NG
>> Repair harness or connector.
All Interior Room Lamps Do Not Operate
INFOID:0000000001328419
1.
CHECK POWER SUPPLY CIRCUIT
1.
All interior room lamps switch are OFF.
2.
Turn ignition switch ON.
3.
Check voltage between BCM harness connector M4 terminal 41
and ground.
OK or NG
OK
>> Repair harness or connector. In a case of making a
short circuit, be sure to disconnect cable from the nega-
tive terminal repairing harness, and then reconnect.
NG
BCS-13, "Removal and Installa-
Bulb Replacement
INFOID:0000000001328420
IGNITION KEY HOLE ILLUMINATION (without Intelligent Key)
1.
Remove combination meter. Refer to
Installation of Combination Meter"
2.
Remove screw and remove NATS antenna amp.
3.
Pull out ring and turn bulb socket to left to release lock.
4.
Installation is the reverse order of removal.
IGNITION KEY HOLE ILLUMINATION (with Intelligent Key)
BCM
connector
Terminal
Front step lamp
connector
Terminal
Continuity
M4
41
Driver side
D9
1
Yes
Passenger
side
D39
1
BCM
connector
Terminal
Rear step lamp connector
Terminal
Continuity
M4
41
LH
D80
1
Yes
RH
D60
1
PKIB3523E
41 – Ground
: Battery voltage.
SKIA5952E
Ignition key hole illumination
: 12 V - 0.8 W
SKIA5575E
INTERIOR ROOM LAMP
LT-165
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
M
A
B
LT
N
O
P
1.
Remove instrument lower panel (driver side). Refer to
.
2.
Turn the bulb socket counterclockwise and unlock it.
3.
Installation is the reverse order of removal.
FRONT STEP LAMP
1.
Remove door finisher. Refer to
2.
Insert a screwdriver in lens and remove lens.
3.
Remove bulb.
4.
Installation is the reverse order of removal.
REAR STEP LAMP
1.
Remove door finisher. Refer to
2.
Insert a screwdriver in lens and remove lens.
3.
Remove bulb.
4.
Installation is the reverse order of removal.
LUGGAGE ROOM LAMP
1.
Remove luggage room lamp. Refer to
.
2.
Remove screw from luggage room lamp.
3.
Insert a suitable tool and remove lens.
4.
Remove bulb.
5.
Installation is the reverse order of removal.
VANITY MIRROR LAMP
Ignition key hole illumination
: 12 V - 0.8 W
PKIC9733E
Step lamp
: 12 V - 5 W
SKIA5564E
Step lamp
: 12 V - 5 W
SKIA5565E
Luggage room lamp
: 12 V - 8 W
SKIA6197E
LT-166
< SERVICE INFORMATION >
INTERIOR ROOM LAMP
1.
Insert a thin screwdriver in the lens end and remove lens.
2.
Remove bulb together with substrate.
3.
Installation is the reverse order of removal.
MAP LAMP
1.
Remove lens using clip driver or suitable tool.
2.
Remove bulb.
3.
Installation is the reverse order of removal.
INTERIOR ROOM LAMP
1.
Remove interior room lamp. Refer to
.
2.
Insert a suitable tool and remove lens.
3.
Remove bulb.
4.
Installation is the reverse order of removal.
PERSONAL LAMP
1.
Remove personal lamp. Refer to
LT-166, "Removal and Installa-
2.
Remove screw from personal lamp.
3.
Insert a screwdriver or similar tool and remove lens.
4.
Remove bulb.
5.
Installation is the reverse order of removal.
Removal and Installation
INFOID:0000000001328421
LUGGAGE ROOM LAMP
Removal
Vanity mirror lamp
: 12 V - 1.32 W
PKIA7806E
Map lamp
: 12 V - 8 W
PKIA2846E
Interior room lamp
:12 V - 10 W
PKIB3637E
Personal lamp
: 12 V - 8 W
SKIA5577E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст