Infiniti FX35 / FX45. Manual — part 867
PS-10
< SERVICE INFORMATION >
STEERING WHEEL
a.
Disconnect lower joint and steering knuckle from steering gear assembly. Refer to
FAX-4, "Removal and Installation"
FAX-11, "Removal and Installation"
b.
Start and run engine at idle to make sure steering fluid has reached normal operating temperature.
c.
While pulling outer socket slowly in
±
11.5 mm (
±
0.453 in) range
from neutral position, make sure rack sliding force is within
specification.
d.
If rack sliding force is not within specification, overhaul steering
gear assembly.
CHECKING FRONT WHEEL TURNING ANGLE
• Check front wheel turning angle after the toe-in inspection. Place
front wheels on turning radius gauges and rear wheels on stands
so that vehicle can be level. Check the maximum inner and outer
wheel turning angles for LH and RH road wheels.
• Start engine and run at idle, turn steering wheel all the way right
and left, measure the turning angle.
• Measure rack stroke if angles are outside the specified value.
• Disassemble steering gear assembly to check the cause that rack
stroke is outside of the standard.
• Steering angles are not adjustable. Check steering gear assembly,
steering column assembly and front suspension components for
wear or damage if any of the turning angles are different from the
specified value. Replace any of them, if any non-standard condi-
tion exists.
Removal and Installation
INFOID:0000000001327713
REMOVAL
NOTE:
When reconnecting spiral cable, fix cable with a tape so that fixing case and rotating part keep aligned. This
will omit neutral position alignment procedure during spiral cable installation.
Rack sliding force
: 147
−
211 N (15
−
21.5 kg, 33
−
47 lb)
SST090B
FAA0016D
Inner wheel (Angle: A)
Minimum
32
°
00’ (32.0
°
)
Nominal
35
°
00’ (35.0
°
)
Maximum
36
°
00’ (36.0
°
)
Outer wheel (Angle: B)
30
°
00’ (30.0
°
)
SGIA0055E
Rack stroke L
67.0 mm (2.638 in)
SGIA0629J
STEERING WHEEL
PS-11
< SERVICE INFORMATION >
C
D
E
F
H
I
J
K
L
M
A
B
PS
N
O
P
1.
Set vehicle to the straight-ahead direction.
2.
Remove driver air bag module. Refer to
SRS-34, "Removal and Installation"
3.
Remove steering wheel lock nut after steering is locked.
4.
Remove steering wheel using the steering wheel puller.
INSTALLATION
Installation is the reverse order of removal. For tightening torque, refer to
PS-12, "Removal and Installation"
NOTE:
Check the spiral cable neutral position after replacing or rotating spiral cable. Refer to
CAUTION:
Do not twist spiral cable freely on excessively after it becomes tight (doing so may cause the cable to
be turn off).
Tool number
A: ST27180001 (J-25726-A)
SGIA1323E
PS-12
< SERVICE INFORMATION >
STEERING COLUMN
STEERING COLUMN
Removal and Installation
INFOID:0000000001327714
COMPONENTS
CAUTION:
• Care must be taken not to give axial impact to steering column assembly during removal and instal-
lation.
• Care must be taken not to move steering gear during removal of steering column assembly.
REMOVAL
1.
Set vehicle to the straight ahead-direction.
2.
Remove driver air bag module from steering wheel. Refer to
3.
Disconnect steering switch connector, remove steering wheel lock nut, then remove steering wheel. Refer
to
.
4.
Remove steering column cover. Refer to
.
5.
Remove combination switch & spiral cable from steering column assembly. Refer to
.
6.
Remove instrument lower panel (driver side). Refer to
.
7.
Remove combination meter. Refer to
1.
Steering wheel
2.
Combination switch & spiral cable
3.
Steering column assembly
4.
Collar
5.
Hole cover seal
6.
Clamp
7.
Hole cover
8.
Lower shaft
9.
Lower joint
Refer to
, for the symbols in the figure.
SGIA1612E
STEERING COLUMN
PS-13
< SERVICE INFORMATION >
C
D
E
F
H
I
J
K
L
M
A
B
PS
N
O
P
8.
Remove fixing bolts of knee protector, then remove knee protec-
tor from vehicle.
9.
Disconnect harness connector from each switch on steering col-
umn shaft, then separate vehicle side harness from it.
10. Remove lock nut and bolt, then separate lower shaft from upper
joint of steering column assembly.
11. Remove fixing bolts and nuts from steering member, remove
steering column assembly from steering member.
12. Remove hole cover seal and clamp.
13. Remove mounting nuts, then remove hole cover from panel.
14. Raise vehicle, then remove mounting bolts of lower joint.
15. Remove lower joint and lower shaft from vehicle.
INSPECTION AFTER REMOVAL
• Check if there is something wrong with jacket tube of steering column assembly and collar etc. And then if
they are damaged, replace with new one.
SGIA0552E
SGIA0554E
SGIA0555E
SGIA0557E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст