Infiniti FX35 / FX45. Manual — part 629
OIL PAN AND OIL STRAINER
EM-33
< SERVICE INFORMATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Apply liquid gasket to oil pan gaskets as shown in the figure.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-44, "Recommended Chemical Product and Sealant"
.
• To install, align protrusion of oil pan gasket with notches of
front timing chain case and rear oil seal retainer.
• Install oil pan gasket with smaller arc to front timing chain case
side.
c.
Install new O-rings on the bottom of cylinder block and oil pump.
d.
Apply a continuous bead of liquid gasket with the tube presser
(commercial service tool) to the cylinder block mating surface of
oil pan (upper) to a limited portion as shown in the figure.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-44, "Recommended Chemical Product and Sealant"
CAUTION:
• For bolt holes with marks (5 locations), apply liquid
gasket outside the holes.
• Apply a bead of 4.5 to 5.5 mm (0.177 to 0.217 in) in diame-
ter to area “A”.
• Attaching should be done within 5 minutes after coating.
e.
Install oil pan (upper).
CAUTION:
Install avoiding misalignment of both oil pan gaskets and O-rings.
PBIC2630E
PBIC1145E
PBIC1144E
PBIC2300E
EM-34
< SERVICE INFORMATION >
[VQ35DE]
OIL PAN AND OIL STRAINER
• Tighten mounting bolts in numerical order as shown in the fig-
ure.
• There are two types of mounting bolts. Refer to the following
for locating bolts.
f.
Tighten transmission joint bolts. Refer to
AT-241, "Removal and Installation (2WD Models)"
.
2.
Install oil strainer to oil pump.
3.
Install oil pan (lower) as follows:
a.
Use scraper to remove old liquid gasket from mating surfaces.
• Also remove old liquid gasket from mating surface of oil pan
(upper).
• Remove old liquid gasket from the bolt holes and thread.
CAUTION:
Do not scratch or damage the mating surfaces when clean-
ing off old liquid gasket.
b.
Apply a continuous bead of liquid gasket with the tube presser
(commercial service tool) to the oil pan (lower) as shown in the
figure.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-44, "Recommended Chemical Product and Sealant"
CAUTION:
Attaching should be done within 5 minutes after coating.
c.
Install oil pan (lower).
M8
×
100 mm (3.94 in)
: 5, 7, 8, 11
M8
×
25 mm (0.98 in)
: Except the above
PBIC0783E
SEM958F
PBIC2657E
OIL PAN AND OIL STRAINER
EM-35
< SERVICE INFORMATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Tighten mounting bolts in numerical order as shown in the fig-
ure.
4.
Install oil pan drain plug.
• Refer to the figure of components of former page for installation direction of drain plug washer. Refer to
EM-30, "Component (2WD Models)"
5.
Install in the reverse order of removal after this step.
NOTE:
At least 30 minutes after oil pan is installed, pour engine oil.
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and adjust engine oil. Refer to
2.
Start engine, and check there is no leak of engine oil.
3.
Stop engine and wait for 10 minutes.
4.
Check the engine oil level again. Refer to
.
Component (AWD Models)
INFOID:0000000001325718
PBIC0782E
SBIA0567E
EM-36
< SERVICE INFORMATION >
[VQ35DE]
OIL PAN AND OIL STRAINER
Removal and Installation (AWD Models)
INFOID:0000000001325719
REMOVAL
CAUTION:
To avoid the danger of being scalded, never drain engine oil when the engine is hot.
NOTE:
To remove oil pan (lower) only, take step 5, then step 24. Removal of step 1, hood assembly (step 2) and step
4 are unnecessary.
1.
Remove front tire.
2.
Remove hood assembly. Refer to
3.
Remove front and rear engine undercover with power tool.
4.
Remove front cross bar with power tool. Refer to
FSU-5, "On-Vehicle Inspection and Service"
.
5.
Drain engine oil. Refer to
CAUTION:
• Perform this step when the engine is cold.
• Do not spill engine oil on drive belts.
6.
Drain engine coolant. Refer to
CO-10, "Changing Engine Coolant"
.
CAUTION:
• Perform this step when the engine is cold.
• Do not spill engine coolant on drive belts.
7.
Remove engine cover with power tool. Refer to
8.
Remove air hose from air duct to mass air flow sensor side and electric throttle control actuator side.
Refer to
.
9.
Remove drive belts. Refer to
EM-15, "Removal and Installation"
10. Remove front drive shaft (LH and RH) and side shaft. Refer to
FAX-13, "On-Vehicle Inspection"
.
11. Remove side shaft. Refer to
FFD-14, "Removal and Installation (VQ35DE Models)"
.
12. Removal engine rear lower slinger, and install engine rear slinger [SST: 10006 31U00 (
—
)] to sling
engine assembly for positioning. Refer to
13. Remove front suspension member. Refer to
FSU-16, "Removal and Installation"
.
14. Remove engine mounting bracket, engine mounting bracket (lower) and insulator. Refer to
.
15. Remove front propeller shaft. Refer to
.
16. Remove oil filter and oil filter bracket. Refer to
17. Remove alternator stay. Refer to
.
18. Remove idler pulley and bracket. Refer to
EM-15, "Removal and Installation"
.
19. Disconnect oil cooler water hoses, and remove oil cooler water pipe mounting bolt. Refer to
20. Disconnect A/T fluid cooler hoses, and remove A/T fluid cooler tube. Refer to
.
21. Remove front final drive assembly. Refer to
FFD-14, "Removal and Installation (VQ35DE Models)"
22. Remove starter motor. Refer to
1.
Oil pan gasket (rear)
2.
Oil pan (upper)
3.
O-ring
4.
Oil pan gasket (front)
5.
Oil filter
6.
Connector bolt
7.
Oil cooler
8.
O-ring
9.
Relief valve
10. Oil filter bracket
11.
Oil filter bracket gasket
12. Oil strainer
13. Drain plug
14. Drain plug washer
15. Oil pan (lower)
16. Rear plate cover
17. Crankshaft position sensor (POS)
18
O-ring (small)
19. O-ring (large)
20. Axle pipe
Slinger bolts:
: 28.0 N·m (2.9 kg-m, 21 ft-lb)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст