Infiniti FX35 / FX45. Manual — part 630
OIL PAN AND OIL STRAINER
EM-37
< SERVICE INFORMATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
23. Remove crankshaft position sensor (POS).
CAUTION:
• Handle carefully to avoid dropping and shocks.
• Do not disassemble.
• Do not allow metal powder to adhere to magnetic part at sensor tip.
• Do not place sensors in a location where they are exposed to magnetism.
24. Remove oil pan (lower) as follows:
a.
Loosen mounting bolts in reverse order as shown in the figure to
remove.
b.
Insert the seal cutter (SST) between oil pan (upper) and oil pan
(lower).
c.
Slide the seal cutter by tapping on the side of tool with a ham-
mer. Remove oil pan (lower).
CAUTION:
• Be careful not to damage the mating surface.
• Do not insert flat-bladed screwdriver, this will damage the
mating surface.
25. Remove oil strainer.
26. Remove transmission joint bolts which pierce oil pan (upper). Refer to
AT-241, "Removal and Installation
27. Loosen mounting bolts in the reverse order as shown in the fig-
ure with power tool to remove.
• Insert the seal cutter [SST: KV10111100 (J37228)] between oil
pan (upper) and cylinder block. Slide seal cutter by tapping on
the side of tool with a hammer. Remove oil pan (upper).
CAUTION:
• Be careful not to damage the mating surfaces.
• Do not insert a screwdriver, this will damage the mating
surfaces.
28. Remove O-rings from bottom of cylinder block and oil pump.
PBIC0782E
SEM960F
PBIC0783E
PBIC1144E
EM-38
< SERVICE INFORMATION >
[VQ35DE]
OIL PAN AND OIL STRAINER
29. Remove oil pan gaskets.
30. Remove axle pipe, as necessary.
• Remove axle pipe from oil pan (upper) using a suitable drift
[outer diameter: 37 mm (1.46 in)].
INSPECTION AFTER REMOVAL
Clean oil strainer if any object attached.
INSTALLATION
1.
Install axle pipe to oil pan, if removed.
• Lubricate O-ring groove of axle pipe, O-ring, and O-ring joint of
oil pan with new engine oil.
Unit: mm (in)
• Install axle pipe to oil pan (upper) from axle pipe flange side
(left side) using a suitable drift [outer diameter: 43 to 57 mm
(1.69 to 2.24 in)].
CAUTION:
Insert it with care to prevent O-ring from sliding.
2.
Install oil pan (upper) as follows:
PBIC1145E
SBIA0469E
Items
O-ring inner diameter
Final drive side (right side)
32 (1.26)
Axle pipe flange side (left side)
34 (1.34)
SBIA0470E
SBIA0471E
OIL PAN AND OIL STRAINER
EM-39
< SERVICE INFORMATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
a.
Use a scraper to remove old liquid gasket from mating surfaces.
CAUTION:
Do not scratch or damage the mating surfaces when clean-
ing off old liquid gasket.
• Also remove old liquid gasket from mating surface of cylinder
block.
• Remove old liquid gasket from the bolt holes and threads.
b.
Install new oil pan gaskets.
• Apply liquid gasket to oil pan gaskets as shown in the figure.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-44, "Recommended Chemical Product and Sealant"
.
• To install, align protrusion of oil pan gasket with notches of
front timing chain case and rear oil seal retainer.
• Install oil pan gasket with smaller arc to front timing chain case
side.
c.
Install new O-rings on the bottom of cylinder block and oil pump.
MEM108A
PBIC2630E
PBIC1145E
PBIC1144E
EM-40
< SERVICE INFORMATION >
[VQ35DE]
OIL PAN AND OIL STRAINER
d.
Apply a continuous bead of liquid gasket with the tube presser
(commercial service tool) to the cylinder block mating surface of
oil pan (upper) to a limited portion as shown in the figure.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-44, "Recommended Chemical Product and Sealant"
CAUTION:
• For bolt holes with marks (5 locations), apply liquid
gasket outside the holes.
• Apply a bead of 4.5 to 5.5 mm (0.177 to 0.217 in) in diame-
ter to area “A”.
• Attaching should be done within 5 minutes after coating.
e.
Install oil pan (upper).
CAUTION:
Install avoiding misalignment of both oil pan gasket and O-rings.
• Tighten mounting bolts in numerical order as shown in the fig-
ure.
• There are two types of mounting bolts. Refer to the following
for locating bolts.
f.
Tighten transmission joint bolts. Refer to
AT-241, "Removal and Installation (2WD Models)"
.
3.
Install oil strainer to oil pump.
4.
Install oil pan (lower) as follows:
a.
Use scraper to remove old liquid gasket from mating surfaces.
• Also remove old liquid gasket from mating surface of oil pan
(upper).
• Remove old liquid gasket from the bolt holes and thread.
CAUTION:
Do not scratch or damage the mating surfaces when clean-
ing off old liquid gasket.
M8
×
100 mm (3.94 in)
: 5, 7, 8, 11
M8
×
25 mm (0.98 in)
: Except the above
PBIC2300E
PBIC0783E
SEM958F
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст