Infiniti FX35 / FX45. Manual — part 631
OIL PAN AND OIL STRAINER
EM-41
< SERVICE INFORMATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
b.
Apply a continuous bead of liquid gasket with the tube presser
(commercial service tool) to the oil pan (lower) as shown in the
figure.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-44, "Recommended Chemical Product and Sealant"
CAUTION:
Attaching should be done within 5 minutes after coating.
c.
Install oil pan (lower).
• Tighten mounting bolts in numerical order as shown in the fig-
ure.
5.
Install oil pan drain plug.
• Refer to the figure of components of former page for installation direction of drain plug washer. Refer to
EM-35, "Component (AWD Models)"
6.
Install in the reverse order of removal after this step.
NOTE:
At least 30 minutes after oil pan is installed, pour engine oil.
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and adjust engine oil. Refer to
2.
Start engine, and check there is no leak of engine oil.
3.
Stop engine and wait for 10 minutes.
4.
Check the engine oil level again. Refer to
.
PBIC2657E
PBIC0782E
EM-42
< SERVICE INFORMATION >
[VQ35DE]
IGNITION COIL
IGNITION COIL
Component
INFOID:0000000001325720
Removal and Installation
INFOID:0000000001325721
REMOVAL
1.
Remove engine cover with power tool. Refer to
2.
Remove air duct (At the left bank side, remove ignition coil). Refer to
.
3.
Move aside harness, harness bracket, and hoses located above ignition coil.
4.
Disconnect harness connector from ignition coil.
5.
Remove ignition coil.
CAUTION:
Do not shock it.
INSTALLATION
Installation is the reverse order of removal.
1.
Ignition coil
2.
Spark plug
3.
Rocker cover (left bank)
A.
Left bank
PBIC4359E
SPARK PLUG (PLATINUM-TIPPED TYPE)
EM-43
< SERVICE INFORMATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
SPARK PLUG (PLATINUM-TIPPED TYPE)
Component
INFOID:0000000001325722
Removal and Installation
INFOID:0000000001325723
REMOVAL
1.
Remove engine cover with power tool. Refer to
2.
Remove ignition coil. Refer to
3.
Remove spark plug with a spark plug wrench (commercial ser-
vice tool).
INSPECTION AFTER REMOVAL
Use the standard type spark plug for normal condition.
The hot type spark plug is suitable when fouling occurs with the standard type spark plug under conditions
such as:
• Frequent engine starts
• Low ambient temperatures
The cold type spark plug is suitable when spark knock occurs with the standard type spark plug under condi-
tions such as:
• Extended highway driving
• Frequent high engine revolution
1.
Ignition coil
2.
Spark plug
3.
Rocker cover (left bank)
A.
Left bank
PBIC4359E
SEM294A
Make
NGK
Standard type
PLFR5A-11
EM-44
< SERVICE INFORMATION >
[VQ35DE]
SPARK PLUG (PLATINUM-TIPPED TYPE)
CAUTION:
• Do not drop or shock spark plug.
• Do not use a wire brush for cleaning.
• If plug tip is covered with carbon, spark plug cleaner may be
used.
• Checking and adjusting plug gap is not required between
change intervals.
INSTALLATION
Installation is the reverse order of removal.
Hot type
PLFR4A-11
Cold type
PLFR6A-11
Gap (Nominal)
: 1.1 mm (0.043 in)
Cleaner air pressure:
Less than 588 kPa (6 kg/cm
2
, 85 psi)
Cleaning time:
Less than 20 seconds
SMA773C
SMA806CA
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст