Infiniti FX35 / FX45. Manual — part 976
WW-26
< SERVICE INFORMATION >
FRONT WIPER AND WASHER SYSTEM
Only washer nozzles (A, B, E, G, H, and K) can be adjusted. Washer nozzles (C, D, F, I, J, and L)
cannot be adjusted because of fixed nozzles.
PKIB3558E
SKIA5073E
FRONT WIPER AND WASHER SYSTEM
WW-27
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
M
A
B
WW
N
O
P
Washer Tube Layout
INFOID:0000000001328568
Removal and Installation of Front Washer Nozzle
INFOID:0000000001328569
Replace wiper arm assembly. Refer to
WW-23, "Removal and Installation of Front Wiper Arms, Adjustment of
.
CAUTION:
Removal/installation of the washer nozzle as a unit must not be done.
Removal and Installation of Front Washer Tube Joint
INFOID:0000000001328570
REMOVAL
1.
Remove upwards while pressing the pawls on reverse side.
2.
Remove washer tube.
INSTALLATION
Installation is the reverse order of removal.
Inspection of Washer Nozzle
INFOID:0000000001328571
CHECK VALVE
Blow check valve. Confirm that the air ventilates. Also confirm that
inhalation is impossible.
CAUTION:
A check valve is provided in the washer fluid line. Be careful not
to connect check valve to washer tube in the wrong direction.
PKID0570E
PKIA1159E
PKIA3131E
WW-28
< SERVICE INFORMATION >
FRONT WIPER AND WASHER SYSTEM
Inspection of Front Wiper and Washer Switch Circuit
INFOID:0000000001328572
LT-104, "Combination Switch Inspection"
Removal and Installation of Front Wiper and Washer Switch
INFOID:0000000001328573
REMOVAL
1.
Remove steering column upper cover. Refer to
2.
Disconnect wiper and washer switch connector.
3.
Pull wiper and washer switch toward the passenger door while
pressing pawls in direction shown by the arrow in the figure, and
remove it from the base.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of Washer Tank
INFOID:0000000001328574
REMOVAL
1.
Remove bolt and pull out washer tank inlet out of washer tank.
2.
Remove front fillet molding (RH). Refer to
3.
Remove fender protector front (RH). Refer to
4.
Remove front bumper fascia assembly. Refer to
5.
Disconnect washer pump connector and wash fluid level sensor
connector.
6.
Remove washer tank mounting bolt and nuts.
PKIB6026E
SKIA5076E
PKIC9705E
FRONT WIPER AND WASHER SYSTEM
WW-29
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
M
A
B
WW
N
O
P
7.
Remove washer tube, and remove washer tank from the vehicle.
INSTALLATION
Installation is the reverse order of removal.
NOTE:
After installation, add water up to the upper level of the washer tank inlet, and check for water leaks.
Removal and Installation of Front and Rear Washer Pump
INFOID:0000000001328575
REMOVAL
1.
Remove fillet molding (RH). Refer to
EI-14, "Component Parts Location"
.
2.
Remove fender protector (RH). Refer to
EI-24, "Component Parts Location"
.
3.
Remove bumper fascia assembly. Refer to
EI-14, "Component Parts Location"
4.
Disconnect washer pump connector and tube.
5.
Pull out front and rear washer pump in direction shown by the
arrow (
) in the figure. Remove front and rear washer pump
from washer tank.
INSTALLATION
Installation is the reverse order of removal.
NOTE:
When installing front and rear washer pump, there should be no packing twists, etc.
PKIC9707E
Washer tank mounting bolt
: 5.7 N·m (0.58 kg-m, 50 in-lb)
Washer tank mounting nut
: 5.7 N·m (0.58 kg-m, 50 in-lb)
Washer tank inlet mounting bolt
: 6.8 N·m (0.69 kg-m, 60 in-lb)
PKIC9706E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст