Infiniti FX35 / FX45. Manual — part 804
STOP LAMP
LT-111
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
M
A
B
LT
N
O
P
TKWM4311E
LT-112
< SERVICE INFORMATION >
STOP LAMP
Terminal and Reference Value for Rear Combination Lamp Control Unit
INFOID:0000000001328374
LT-86, "Terminal and Reference Value for Rear Combination Lamp Control Unit"
Stop Lamp Does Not Operate
INFOID:0000000001328375
1.
CHECK TAIL LAMP AND TURN SIGNAL LAMP
Make sure tail lamps and turn signal lamps is illuminated.
TKWM4312E
STOP LAMP
LT-113
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
M
A
B
LT
N
O
P
OK or NG
OK
>> GO TO 2.
NG
>> GO TO 6.
2.
CHECK FUSE
Check fuse No.20 is blow out.
OK or NG
OK
>> GO TO 3.
NG
>> If fuse is blow out, be sure to eliminate cause of problem before installing new fuse.
3.
CHECK INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Check voltage between rear combination lamp control unit har-
ness connector and ground.
OK or NG
OK
>> Replace rear combination lamp control unit.
NG
>> GO TO 4.
4.
CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT
1.
Disconnect stop lamp switch connector.
2.
Check voltage between stop lamp switch harness connector
E210 terminal 1 and ground.
OK or NG
OK
>> GO TO 5.
NG
>> Repair harness or connector.
5.
CHECK STOP LAMP SWITCH CIRCUIT
1.
Disconnect rear combination lamp control unit connector.
2.
Check continuity between stop lamp switch harness connector
E210 terminal 2 and rear combination lamp control unit harness
connector B65 terminal 3.
OK or NG
OK
>> Replace stop lamp switch.
NG
>> Repair harness or connector.
6.
CHECK POWER SUPPLY CIRCUIT
(+)
(-)
Condition
Voltage
BCM con-
nector
Terminal
B65
3
Ground
Stop lamp switch is ON.
(Depressed)
Battery
voltage
Stop lamp switch is OFF.
(Released)
Approx. 0 V
PKIA5233E
1 – Ground
: Battery voltage.
PKIA5234E
2 – 3
: Continuity should exist.
PKIA5235E
LT-114
< SERVICE INFORMATION >
STOP LAMP
1.
Disconnect rear combination lamp control unit connector.
2.
Check voltage between rear combination lamp control unit har-
ness connector B65 terminal 1 and ground.
OK or NG
OK
>> GO TO 7.
NG
>> Repair harness or connector.
7.
CHECK GROUND CIRCUIT
Check continuity between rear combination lamp control unit har-
ness connector B65 terminal 7 and ground.
OK or NG
OK
>> GO TO 8.
NG
>> Repair harness or connector.
8.
CHECK STOP LAMPS CIRCUIT
1.
Disconnect rear combination lamp RH and LH connectors.
2.
Check continuity between rear combination lamp control unit
harness connector B65 terminal 11 and rear combination lamp
LH harness connector B57 terminal 3.
3.
Check continuity between rear combination lamp control unit
harness connector B65 terminal 10 and rear combination lamp
LH harness connector B57 terminal 4.
4.
Check continuity between rear combination lamp control unit harness connector B65 terminal 9 and rear
combination lamp RH harness connector B219 terminal 3.
5.
Check continuity between rear combination lamp control unit harness connector B65 terminal 8 and rear
combination lamp RH harness connector B219 terminal 4.
OK or NG
OK
>> Replace rear combination lamp control unit or rear combination lamp, and then check if turn signal
lamps is illuminated.
NG
>> Repair harness or connector.
High-Mounted Stop Lamp
INFOID:0000000001328376
BULB REPLACEMENT, REMOVAL AND INSTALLATION
1 – Ground
: Battery voltage.
SKIA5907E
7 – Ground
: Continuity should exist.
SKIA5908E
11 – 3
: Continuity should exist.
10 – 4
: Continuity should exist.
9 – 3
: Continuity should exist.
8 – 4
: Continuity should exist.
SKIA5910E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст