Infiniti FX35 / FX45. Manual — part 634
ROCKER COVER
EM-53
< SERVICE INFORMATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
4.
Tighten bolts in two steps separately in numerical order as
shown in the figure.
5.
Install oil catcher and oil filer cap to rocker cover (left bank), if removed.
6.
Install new O-ring and PCV valve to rocker cover (right bank), if removed.
7.
Install PCV hose.
• Insert PCV hose by 25 to 30 mm (0.98 to 1.18 in) from connector end.
• When installing, be careful not to twist or come in contact with other parts.
• Install PCV hose between right and left rocker covers with its identification paint facing upward (right
rocker cover side). Refer to component figure in "Removal and Installation".
8.
Install in the reverse order of removal after this step.
1st step
: 1.96 N·m (0.20 kg-m, 17 in-lb)
2nd step
: 8.33 N·m (0.85 kg-m, 74 in-lb)
KBIA0985E
EM-54
< SERVICE INFORMATION >
[VQ35DE]
FRONT TIMING CHAIN CASE
FRONT TIMING CHAIN CASE
Removal and Installation
INFOID:0000000001325728
NOTE:
• This section describes removal/installation procedure of front timing chain case and timing chain related
parts without removing oil pan (upper) on the vehicle.
• When oil pan (upper) needs to be removed or installed, or when rear timing chain case is removed or
installed, remove oil pans (upper and lower) first. Then remove front timing chain case, timing chain related
parts, and rear timing chain case in this order, and install in reverse order of removal. Refer to
• Refer to
for component parts location.
REMOVAL
1.
Disconnect negative battery terminal. Refer to
2.
Remove engine cover with power tool. Refer to
3.
Remove air cleaner case assembly. Refer to
.
4.
Remove front and rear engine undercover with power tool.
5.
Release the fuel pressure. Refer to
6.
Drain engine oil. Refer to
CAUTION:
• Perform this step when the engine is cold.
• Do not spill engine oil on drive belts.
7.
Drain engine coolant from radiator. Refer to
CO-10, "Changing Engine Coolant"
.
CAUTION:
• Perform this step when the engine is cold.
• Do not spill engine coolant on drive belts.
8.
Separate engine harnesses removing their brackets from front timing chain case.
9.
Remove drive belts. Refer to
EM-15, "Removal and Installation"
10. Remove intake manifold collectors (upper and lower). Refer to
.
11. Remove power steering oil pump from bracket with piping connected, and temporarily secure it aside.
PS-27, "On-Vehicle Inspection and Service"
12. Remove power steering oil pump bracket. Refer to
PS-27, "On-Vehicle Inspection and Service"
13. Remove alternator. Refer to
14. Remove water bypass hose, water hose clamp and idler pulley bracket from front timing chain case.
15. Remove intake valve timing control covers.
• Loosen mounting bolts in reverse order as shown in the figure.
• Use the seal cutter [SST: KV10111100 (J37228)] to cut liquid
gasket for removal.
CAUTION:
Shaft is internally jointed with camshaft sprocket (INT) cen-
ter hole. When removing, keep it horizontal until it is com-
pletely disconnected.
SEM728G
FRONT TIMING CHAIN CASE
EM-55
< SERVICE INFORMATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
16. Remove collared O-ring from front timing chain case (left and
right side).
17. Remove rocker covers (right and left banks). Refer to
.
NOTE:
When only timing chain (primary) is removed, rocker cover does not need to be removed.
18. Obtain No. 1 cylinder at TDC of its compression stroke as follows:
NOTE:
When timing chain is not removed/installed, this step is not required.
a.
Rotate crankshaft pulley clockwise to align timing mark (grooved
line without color) with timing indicator.
b.
Make sure that intake and exhaust cam noses on No. 1 cylinder
(engine front side of right bank) are located as shown in the fig-
ure.
• If not, turn crankshaft one revolution (360 degrees) and align
as shown in the figure.
NOTE:
When only timing chain (primary) is removed, rocker cover does
not need to be removed. To make sure that No. 1 cylinder is at
its compression TDC, remove front timing chain case first. Then
check mating marks on camshaft sprockets. Refer to
19. Remove crankshaft pulley as follows:
a.
Remove rear cover plate (2WD models) or starter motor (AWD models) and set ring gear stopper (SST).
Refer to
EM-30, "Component (2WD Models)"
(2WD models) or
(AWD mod-
els).
b.
Loosen crankshaft pulley bolt and locate bolt seating surface as
10 mm (0.39 in) from its original position.
CAUTION:
Do not remove crankshaft pulley bolt as it will be used as a
supporting point for suitable puller.
PBIC2631E
KBIA1717J
SEM418G
PBIC1103E
EM-56
< SERVICE INFORMATION >
[VQ35DE]
FRONT TIMING CHAIN CASE
c.
Place suitable puller tab on holes of crankshaft pulley, and pull
crankshaft pulley through.
CAUTION:
Do not put suitable puller tab on crankshaft pulley periph-
ery, as this will damage internal damper.
20. Remove oil pan (lower). Refer to
EM-30, "Component (2WD Models)"
.
21. Loosen two mounting bolts in front of oil pan (upper) with power
tool in reverse order shown in figure.
22. Remove front timing chain case as follows:
a.
Loosen mounting bolts with power tool in reverse order as
shown in the figure.
b.
Insert suitable tool into the notch at the top of front timing chain
case as shown (1).
c.
Pry off case by moving a tool as shown (2).
• Use the seal cutter [SST: KV10111100 (J37228)] to cut liquid
gasket for removal.
CAUTION:
• Do not use a screwdrivers or something similar.
• After removal, handle front timing chain case carefully
so it does not tilt, cant, or warp under a load.
EMQ0477D
PBIC1116E
KBIA1303E
SEM156F
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст