Infiniti FX35 / FX45. Manual — part 698
FFD-2
< SERVICE INFORMATION >
PRECAUTIONS
SERVICE INFORMATION
PRECAUTIONS
Service Notice or Precaution
INFOID:0000000001327476
• Check for the correct installation status prior to removal or disassembly. If matching marks are required, be
certain they do not interfere with the function of the parts when applied.
• Overhaul should be done in a clean work area, it is preferable to work in dustproof area.
• Before disassembly, using steam or white gasoline, completely remove sand and mud from the exterior of
the unit, preventing them from entering into the unit during disassembly or assembly.
• Check appearance of the disassembled parts for damage, deformation, and unusual wear. Replace them
with a new ones if necessary.
• Gaskets, seals and O-rings should be replaced any time when the unit is disassembled.
• In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to outside. If tight-
ening sequence is specified, observe it.
• Clean and flush the parts sufficiently and blow-dry them.
• Be careful not to damage sliding surfaces and mating surfaces.
• When applying sealant, remove the old sealant from the mounting surface; then remove any moisture, oil,
and foreign materials from the application and mounting surfaces.
• Always use shop paper for cleaning the inside of components.
• Avoid using cotton gloves or shop rags to prevent entering of lint.
• During assembly, observe the specified tightening torque, and apply new gear oil, petroleum jelly, or multi-
purpose grease as specified for each vehicle, if necessary.
PREPARATION
FFD-3
< SERVICE INFORMATION >
C
E
F
G
H
I
J
K
L
M
A
B
FFD
N
O
P
PREPARATION
Special Service Tool
INFOID:0000000001327477
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
KV381054S0
(J-34286)
Puller
• Removing front oil seal
• Removing side bearing outer race
ST33400001
(J-26082)
Drift
a: 60 mm (2.36 in) dia.
b: 47 mm (1.85 in) dia.
• Installing front oil seal
• Installing side oil seal (right side)
KV38102510
(
—
)
Drift
a: 71 mm (2.80 in) dia.
b: 65 mm (2.56 in) dia.
Installing front oil seal
KV38102100
(J-25803-01)
Drift
a: 44 mm (1.73 in) dia.
b: 36 mm (1.42 in) dia.
c: 24.5 mm (0.965 in) dia.
Installing side oil seal (left side)
ST30032000
(J-26010-01)
Drift
a: 80 mm (3.15 in) dia.
b: 38 mm (1.50 in) dia.
c: 31 mm (1.22 in) dia.
• Installing drive pinion rear bearing inner
race
• Installing side shaft
ST3127S000
(J-25765-A)
Preload gauge
1: GG91030000
(J-25765)
Torque wrench
2: HT62940000
(
—
)
Socket adapter (1/2
″
)
3: HT62900000
(
—
)
Socket adapter (3/8
″
)
Measuring pinion bearing preload and total
preload
ZZA0601D
ZZA0702D
ZZA0838D
ZZA1046D
S-NT107
NT124
FFD-4
< SERVICE INFORMATION >
PREPARATION
KV10111100
(J-37228)
Seal cutter
Removing carrier cover
ST3306S001
(J-22888-D)
Differential side bearing puller set
1: ST33051001
(J-22888-20)
Puller
2: ST33061000
(J-8107-2)
Base
a: 28.5 mm (1.122 in) dia.
b: 38 mm (1.50 in) dia.
Removing and installing side bearing inner
race
ST30031000
(J-22912-01)
Replacer
Removing pinion rear bearing inner race
KV31103000
(J-38982)
Drift
a: 49 mm (1.93 in) dia.
b: 70 mm (2.76 in) dia.
Installing side bearing outer race
ST30611000
(J-25742-1)
Drift bar
Installing side bearing outer race (Use with
KV31103000)
ST37820000
(
—
)
Drift
a: 39 mm (1.54 in) dia.
b: 72 mm (2.83 in) dia.
Installing drive pinion front and rear bearing
outer race
Tool number
(Kent-Moore No.)
Tool name
Description
S-NT046
NT072
ZZA0700D
ZZA1113D
S-NT090
ZZA0836D
PREPARATION
FFD-5
< SERVICE INFORMATION >
C
E
F
G
H
I
J
K
L
M
A
B
FFD
N
O
P
Commercial Service Tool
INFOID:0000000001327478
ST33230000
(J-25805-01)
Drift
a: 51 mm (2.01 in) dia.
b: 41 mm (1.61 in) dia.
c: 28.5 mm (1.122 in) dia.
Installing side bearing inner race
KV38100200
(
—
)
Drift
a: 65 mm (2.56 in) dia.
b: 49 mm (1.93 in) dia.
Installing side shaft oil seal
(J-8129)
Spring gauge
Measuring turning torque
Tool number
(Kent-Moore No.)
Tool name
Description
ZZA1046D
ZZA1143D
NT127
Tool name
Description
Flange wrench
Removing and installing drive pinion lock nut
Spacer
a: 60 mm (2.36 in) dia.
b: 36 mm (1.42 in) dia.
c: 30 mm (1.18 in)
Installing pinion front bearing inner race
Power tool
Loosening bolts and nuts
NT771
ZZA1133D
PBIC0190E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст