Infiniti FX35 / FX45. Manual — part 697

    FAX-24

    < SERVICE INFORMATION >

    [AWD]

    FRONT DRIVE SHAFT

    3.

    Line up alignment marks which were made when spider assem-
    bly was removed. Install spider assembly, with serration chamfer
    facing dive shaft.

    4.

    Secure spider assembly with snap ring.
    NOTE:
    Discard old snap ring; replace with new one.

    5.

    Apply Nissan genuine grease or equivalent to spider assembly
    and sliding surface.

    6.

    Install housing to spider assembly. Apply Nissan genuine grease
    or equivalent to housing.

    7.

    Install boot securely into grooves (indicated by * marks) shown
    in the figure.

    CAUTION:

    If there is grease on boot mounting surfaces (indicated by*
    marks) of shaft and housing, boot may come off. Remove
    all grease from surfaces.

    8.

    Make sure boot installation length “L” is the length indicated
    below. Insert a flat-bladed screwdriver or similar tool into smaller
    side of boot. Bleed air from boot to prevent boot deformation.

    CAUTION:

    • Boot may break if boot installation length is less than standard value.
    • Take care not to touch the tip of screwdriver to inside surface of boot.

    9.

    Install new larger and smaller boot bands securely.
    NOTE:
    Discard old boot bands; replace with new ones.

    SDIA2629E

    SFA023A

    Grease amount

    : 113

    −

    123 g (3.98

    −

    4.33 oz)

    SDIA1446E

    Boot installation Length “L”:

    157.55

    −

    159.55 mm (6.20

    −

    6.28 in)

    SDIA3250E

    FRONT DRIVE SHAFT

    FAX-25

    < SERVICE INFORMATION >

    [AWD]

    C

    E

    F

    G

    H

    I

    J

    K

    L

    M

    A

    B

    FAX

    N

    O

    P

    10. Put boot band in the groove on drive shaft boot. Then fit pawls

    (

    ) into holes to temporary installation.

    NOTE:
    For the large diameter side, fit projection (A) and guide slit (B) at
    first.

    11. Pinch projection on the band with suitable pliers to tighten band.
    12. Insert tip of band below end of the pawl.

    13. After installing housing and shaft, rotate boot to check whether

    or not the actual position is correct. If boot position is not correct,
    secure boot with new boot bands again.

    14. Install circular clip.

    NOTE:
    Discard old circular clip; replace with new one.

    Wheel Side

    Assemble in steps 14 to 23 of

    FAX-13, "On-Vehicle Inspection"

    .

    SDIA3557E

    SDIA3558E

    FAX-26

    < SERVICE INFORMATION >

    [AWD]

    SERVICE DATA AND SPECIFICATIONS (SDS)

    SERVICE DATA AND SPECIFICATIONS (SDS)

    Wheel Bearing

    INFOID:0000000001327520

    Drive Shaft

    INFOID:0000000001327521

    Axial end play

    0.05 mm (0.002 in) or less

    Joint

    Wheel side

    Front final drive assembly side

    Engine type

    VQ35DE models

    VK45DE models

    VQ35DE models

    VK45DE models

    Grease quantity

    LH side

    77 – 97 g (2.71 – 3.42 oz)

    95 – 105 g (3.35 – 3.70 oz)

    RH side

    113 – 123 g (3.98 – 4.33 oz)

    Boots installed length

    LH side

    136 mm (5.35 in)

    150.9 – 152.9 mm (5.94

    – 6.02 in)

    95 – 97 mm

    (3.74 – 3.82 in)

    RH side

    157.55 – 159.55 mm (6.20 – 6.28 in)

    Была ли эта страница вам полезна?
    Да!Нет
    5 посетителей считают эту страницу полезной.
    Большое спасибо!
    Ваше мнение очень важно для нас.

    Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.

    Текст

    Матвей Александрович14.05.2024 06:37
    Политика конфиденциальности