Infiniti FX35 / FX45. Manual — part 885
RF-22
< SERVICE INFORMATION >
SUNROOF
2.
After loosening glass lid TORX bolts (left and right), tilt down
glass lid.
3.
Adjust glass lid from outside of vehicle so it resembles “A–A” “B–
B” “C–C” as shown in the figure to the right.
4.
To prevent glass lid from moving after adjustment, first tighten
the TORX bolts of front left, and then tighten the TORX bolts of
rear right.
5.
Tighten remaining TORX bolts, being careful to prevent glass lid
from moving.
6.
Tilt glass lid up and down several times to make sure it moves
smoothly.
Removal and Installation
INFOID:0000000001328050
• After any adjustment, check sunroof operation and glass lid alignment.
• Handle finisher plate and glass lid with care so as not to cause damage.
• It is desirable for easy installation to mark each point before removal.
CAUTION:
• Always work with a helper.
• Fully close the glass lid assembly, before removal, then do not operate motor assembly after
removal.
PIIA3501E
SUNROOF
RF-23
< SERVICE INFORMATION >
C
D
E
F
G
H
J
K
L
M
A
B
RF
N
O
P
PIIA6190E
1. Glass lid
2. TORX bolt
3. Washer
4. Rear sunroof bracket
5. Front sunroof bracket
6. Wind deflector
7. Sunroof unit assembly
8. Noise cover
9. Sunroof motor assembly
10. Screw
11.
Sunshade
12. Nut
13. Bolt
14. Drain plate
15. Sunshade stopper
16. Drain hose
RF-24
< SERVICE INFORMATION >
SUNROOF
SUNROOF UNIT ASSEMBLY
Removal
CAUTION:
• Always work with a helper.
• When taking sunroof unit out, use clothes to protect the seats and trim from damage.
• After installing the sunroof unit and glass lid, be sure to perform the leakage test and make sure
there is no malfunction.
1.
Tilt up glass lid.
2.
Remove the headlining. Refer to
EI-43, "Component Parts Location"
3.
Disconnect drain hoses.
4.
Remove glass lid. Refer to
RF-22, "Removal and Installation"
5.
Remove motor mounting screws. Remove sunroof motor
assembly and disconnect harness connector.
CAUTION:
• Before removing sunroof motor assembly, make sure that
sunroof is fully closed.
• After removing sunroof motor assembly, do not attempt to
rotate sunroof motor as a single unit.
6.
Remove nuts on the front end and side rail.
7.
Remove curtain air bag bracket bolts, then remove curtain air
bag bracket from the rail side. Refer to
.
8.
Remove front/rear sunroof bracket bolts, then remove sunroof
unit assembly from roof panel.
9.
Remove sunroof unit assembly through the passenger room while being careful not to damage the seats
and trim.
Installation
PIIA6189E
PIIA6191E
PIIA6193E
SUNROOF
RF-25
< SERVICE INFORMATION >
C
D
E
F
G
H
J
K
L
M
A
B
RF
N
O
P
1.
Temporarily tighten the mounting bolts on the front/rear sunroof
brackets (RH/LH).
2.
Bring sunroof unit assembly into passenger room and place the
rear end of the rail onto the sunroof brackets.
3.
Tighten the mounting nuts on the front end.
4.
Tighten the installation points diagonally excluding the installation point of the sunroof bracket around the
roof opening.
5.
Tighten the bolts on the sunroof bracket to the vehicle side and
then tighten the bolt to the rail side.
6.
Tighten the bolts on the curtain air bag bracket to the rail side.
Refer to
SRS-40, "Removal and Installation"
GLASS LID
Removal
1.
Tilt up glass lid.
2.
Remove TORX bolts from remove glass lid.
Installation
1.
Tighten bolts diagonally on the glass lid.
2.
After installation, carry out fitting adjustment.
SUNSHADE
PIIA6193E
PIIA6191E
PIIA6193E
PIIA6192E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст