Infiniti M45 (Y34). Manual — part 220
DOOR
BL-105
C
D
E
F
G
H
J
K
L
M
A
B
BL
INSTALLATION
Install in the reverse order of removal.
Removal and Installation of Rear Door
AIS001ON
REMOVAL
CAUTION:
●
When removing and installing the rear door assembly, support the door with a jack and cloth to
protect the door and body.
●
When removing and installing rear door assembly, be sure to carry out the fitting adjustment Refer
to
●
Operate with two workers, because of its heavy weight.
●
Check the hinge rotating part for poor lubrication. If necessary, apply “body grease”.
●
After installing, check operation.
1.
Grommet is pulled out, and the Rear door harness connector is
detached.
2.
Remove the mounting bolts of the check link on the vehicle.
3.
Remove the door-side hinge mounting nuts, and remove the
door assembly.
INSTALLATION
Install in the reverse order of assembly.
PIIA2787E
PIIA2788E
PIIA3058E
BL-106
DOOR
Door Weatherstrip
AIS001EB
REMOVAL
Remove the weatherstrip clips and remove weatherstrip.
CAUTION:
After removal, do not pull strongly on the weatherstrip.
INSTALLATION
Install in the reverse order of removal.
PIIA3062E
FRONT DOOR LOCK
BL-107
C
D
E
F
G
H
J
K
L
M
A
B
BL
FRONT DOOR LOCK
PFP:80502
Component Structure
AIS001EC
Inspection and Adjustment
AIS001ED
1.
Remove the front door finisher. Refer to
EI-31, "Removal and Installation"
2.
Remove the sealing screen assembly.
3.
Remove the front door window. Refer to
GW-47, "Removal and Installation"
BELL CRANK ADJUSTMENT
CAUTION:
Before adjusting bell crank, make sure that rod is installed to inside handle.
●
After installing door lock and inside handle, set them in the lock position.
●
Using a flat-bladed screwdriver, expand rod holder.
●
Remove rod free play at joining area and set rod in position.
●
After adjusting bell crank adjustment have been made, operate
door lock knob, door lock switch and door key to make sure that
they lock and unlock properly.
1.
Key cylinder (driver side only)
2.
Outside handle
3.
Key lock rod (driver side only)
4.
Outside handle rod
5.
Door lock assembly
6.
Door lock actuator
7.
Knob rod protector
8.
Lock knob rod
9.
Inside handle rod
10. Bell crank
11.
Lock knob rod
12. Lock knob
13. Inside handle
14. Inside handle escutcheon A
PIIA2776E
PIIA2777E
BL-108
FRONT DOOR LOCK
EXTERIOR HANDLE ROD ADJUSTMENT
Rotate the bushing to adjust so that the clearance between the bush-
ing and rod becomes as shown in the figure.
CAUTION:
Be careful not to make the clearance 0 mm (0 in) or the rod
pressed continuously.
Removal and Installation
AIS001EE
REMOVAL
1.
Remove the front door finisher. Refer to
EI-31, "Removal and Installation"
.
2.
Remove the sealing screen assembly.
3.
Remove the front door window. Refer to
GW-47, "Removal and Installation"
.
4.
Remove the inside handle escutcheon A.
5.
Remove the mounting screw, and remove the inside handle.
6.
Disconnect bell crank lock knob rod at the joints.
7.
Disconnect inside handle rod door lock assembly side.
8.
Slide inside handle rearward and remove it.
9.
Remove the mounting screws, remove the knob rod protector.
10. Reach to separate the key cylinder rod (driver side only) and exterior handle rod connection (on the han-
dle).
11. Disconnect the door lock actuator connector.
12. Remove the mounting bolts (TORX T30), remove the door lock
assembly.
SBT978
PIIA2778E
PIIA1090E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст