Infiniti M45 (Y34). Manual — part 221
FRONT DOOR LOCK
BL-109
C
D
E
F
G
H
J
K
L
M
A
B
BL
13. Remove the exterior handle mounting bolts, move the exterior
handle assembly backward, and then remove it from the panel
in front of the exterior handle escutcheon.
14. Using a screwdriver or similar tool, remove the door key cylinder status switch from the key cylinder
(driver side only).
15. Using a clip driver or similar tool, remove the bell crank's plastic
clip.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
●
To install each rod, be sure to rotate the rod holder until a click is felt.
●
After installing, check operation.
●
After installing, perform fitting adjustment. Refer to
Disassembly and Assembly
AIS001EF
DISASSEMBLY
CAUTION:
Be sure to remove or install the actuator with the door lock assembly removed.
1.
Remove the mounting screws, and remove the actuator from the
door lock assembly.
2.
Pull the actuator straight downward to separate it from the door
lock assembly.
ASSEMBLY
1.
Align the actuator pivot with the cutout on the knob lever of the door lock assembly, then assemble the
actuator.
2.
Move the knob lever and the actuator pivot toward the lock-on direction, and check that it engages
securely.
PIIA2779E
PIIA2780E
PIIA2781E
BL-110
REAR DOOR LOCK
REAR DOOR LOCK
PFP:82502
Components
AIS001EG
Inspection and Adjustment
AIS001EH
1.
Remove the rear door finisher. Refer to
EI-31, "Removal and Installation"
.
2.
Remove the sealing screen assembly.
3.
Remove the rear window. Refer to
GW-53, "Removal and Installation"
EXTERIOR HANDLE ROD ADJUSTMENT
Rotate the bushing to adjust so that the clearance between the bush-
ing and rod becomes as shown in the figure.
CAUTION:
Be careful not to make the clearance 0 mm (0 in) or the rod
pressed continuously.
Removal and Installation
AIS001Q4
REMOVAL
1.
Remove the rear door finisher. Refer to
EI-31, "Removal and Installation"
.
2.
Remove the sealing screen assembly
3.
Remove the rear door window. Refer to
GW-53, "Removal and Installation"
4.
Remove the inside handle escutcheon A.
5.
Remove the mounting screw, and remove the inside handle.
1.
Outside handle rod
2.
Outside handle
3.
Door lock assembly
4.
Door lock actuator
5.
Knob rod protector
6.
Inside handle rod
7.
Rod holder
8.
Lock knob rod
9.
Lock knob
10. Inside handle
11.
Inside handle escutcheon A
PIIA2782E
SBT978
REAR DOOR LOCK
BL-111
C
D
E
F
G
H
J
K
L
M
A
B
BL
6.
Using a screwdriver or similar tool, open the rod holder and
remove the rod.
7.
Remove the mounting screws and nut, remove the knob rod protector.
8.
Disconnect inside handle rod door lock assembly side.
9.
Slide inside handle rearward and remove it.
10. Disconnect the door lock actuator connector.
11. Remove the mounting bolts (TORX T30), remove the door lock
assembly.
12. Remove the exterior handle mounting bolts, move the exterior
handle assembly backward, and then remove it from the panel
in front of the exterior handle escutcheon.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
●
To install each rod, be sure to rotate the rod holder until a click is felt.
●
After installing, check operation.
●
After installing, perform fitting adjustment. Refer to
PIIA2784E
PIIA2783E
PIIA1090E
PIIA2779E
BL-112
REAR DOOR LOCK
Disassembly and Assembly
AIS001EJ
DISASSEMBLY
CAUTION:
Be sure to remove or install the actuator with the door lock assembly removed.
1.
Remove the mounting screws, and remove the actuator from the
door lock assembly.
2.
Pull the actuator straight downward to separate it from the door
lock assembly.
ASSEMBLY
1.
Align the actuator pivot with the cutout on the knob lever of the door lock assembly, then assemble the
actuator.
2.
Move the knob lever and the actuator pivot toward the lock-on direction, and check that it engages
securely.
PIIA2786E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст