Infiniti M45 (Y34). Manual — part 222
TRUNK LID
BL-113
C
D
E
F
G
H
J
K
L
M
A
B
BL
TRUNK LID
PFP:H4300
Fitting Adjustment
AIS001EK
LONGITUDINAL AND LATERAL CLEARANCE ADJUSTMENT
1.
With the striker released, loosen the trunk lid hinge mounting bolts to close the trunk lid.
2.
Make the lateral clearance and the clearance to the rear window glass equal, and open the trunk lid to
tighten the mounting bolts to the specified torque.
SURFACE HEIGHT ADJUSTMENT
1.
Loosen the striker mounting bolts. Raise the striker to the top position, and temporarily tighten the upper
mounting bolt at the position.
2.
Close the trunk lid lightly and adjust the surface height, then open the trunk lid to finally tighten the striker
mounting bolts to the specified torque.
PIIA3064E
BL-114
TRUNK LID
Removal and Installation of Trunk Lid Assembly
AIS001EL
REMOVAL
1.
Remove the trunk lid finisher. Refer to
EI-42, "TRUNK ROOM TRIM & TRUNK LID FINISHER"
2.
Disconnect the connectors in the trunk lid, and remove the harness clamps to pull the harness out of the
trunk lid.
3.
Support the trunk lid striker with a proper material to prevent it
from falling.
WARNING:
Body injury may occur if no supporting rod is holding the
trunk lid open when removing the damper stay.
4.
Remove the mounting bolts, and remove the trunk lid assembly.
CAUTION:
Operate with two workers, because of its heavy weight.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
●
After installing, apply touch-up paint (the body color) onto the head of the hinge mounting bolts.
●
After installing, check operation.
●
After installing, perform fitting adjustment. Refer to
Removal and Installation of Trunk Lid Stay
AIS0026W
REMOVAL
1.
Remove the rear seat cushion. Refer to
SE-133, "Removal and Installation"
2.
Remove the rear seat back. Refer to
SE-133, "Removal and Installation"
3.
Remove the rear parcel shelf finisher. Refer to
EI-37, "Removal and Installation"
.
4.
Remove the trunk front finisher. Refer to
EI-42, "TRUNK ROOM TRIM & TRUNK LID FINISHER"
.
1.
Trunk lid assembly
2.
Trunk lid hinge
3.
Trunk lid emergency opener lever
4.
Bolt
5.
Trunk lid harness
6.
Trunk lid lock
PIIB1536E
PIIA3060E
TRUNK LID
BL-115
C
D
E
F
G
H
J
K
L
M
A
B
BL
5.
Support the trunk lid closure & striker with a proper material to
prevent it from falling.
WARNING:
Body injury may occur if no supporting rod is holding the
trunk lid open when removing the damper stay.
6.
Remove the mounting bolts on rear parcel shelf.
7.
Remove the mounting nuts on trunk lid hinge, and remove trunk
lid stay.
INSTALLTION
Install in the reverse order of removal.
Removal and Installation of Trunk Lid Lock
AIS001Q8
REMOVAL
1.
Remove the trunk lid finisher. Refer to
EI-42, "TRUNK ROOM TRIM & TRUNK LID FINISHER"
2.
Separate the key cylinder rod.
3.
After removing the harness connector, remove the mounting
bolts, and remove the trunk lid lock.
INSTALLTION
Install in the reverse order of removal.
PIIA3060E
PIIA3069E
PIIA3068E
PIIA3056E
BL-116
TRUNK LID
Removal and Installation of Trunk Closure Control Unit
AIS001Q9
REMOVAL
1.
Remove the trunk rear finisher. Refer to
EI-42, "TRUNK ROOM TRIM & TRUNK LID FINISHER"
2.
After removing trunk lid closure control unit, remove the harness
connector, remove the mounting bolts, and remove the trunk clo-
sure control unit.
CAUTION:
●
After installing, check operation.
●
After installing, perform fitting adjustment. Refer to
INSTALLATION
Install in the reverse order of removal.
Removal and Installation of Trunk Lid Weatherstrip
AIS001EN
REMOVAL
1.
Pull up and remove engagement with body from weatherstrip joint.
CAUTION:
After removal, do not pull strongly on the weatherstrip.
INSTALLATION
1.
Working from the upper section, align weatherstrip mark with vehicle center position mark and install
weatherstrip onto the vehicle.
2.
For the lower section, align the weatherstrip seam with center of the striker.
3.
After installation, pull the weatherstrip gently to ensure that there is no loose section.
NOTE:
Make sure the weatherstrip is fit tightly at each corner and back door rear plate.
PIIA3067E
PIIA3063E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст