Infiniti M45 (Y34). Manual — part 126
ASSEMBLY
AT-389
D
E
F
G
H
I
J
K
L
M
A
B
AT
b.
Measure dimension “L”.
c.
Calculate dimension “J”.
2.
Measure dimensions “M
1
” and “M
2
” and then calculate dimen-
sion “M”.
a.
Place bearing race and needle bearing on oil pump assembly.
b.
Measure thickness of straightedge “M
1
”.
c.
Measure thickness of straightedge “M
2
”.
“J”: Distance between oil pump fitting surface of
transmission case and needle bearing mating surface
of front sun gear.
J = K – L
SCIA5352E
SCIA3125E
SCIA3124E
SCIA3126E
SCIA3127E
AT-390
ASSEMBLY
d.
Calculate dimension “M”.
3.
Adjust total end play “T
1
”.
●
Select proper thickness of bearing race so that total end play
is within specifications.
Assembly (2)
ACS004HK
CAUTION:
When replacing the control valve assembly, erase EEP ROM in TCM. Refer to
TCM, A/T Assembly and Control Valve Assembly Replacement"
.
1.
Install O-ring in oil pump assembly.
CAUTION:
●
Do not reuse O-ring.
●
Apply ATF to O-ring.
2.
Install bearing race in oil pump assembly.
CAUTION:
Apply petroleum jelly to bearing race.
“M”: Distance between transmission case fitting sur-
face of oil pump and needle bearing on oil pump.
M = M
1
– M
2
SCIA3125E
T
1
= J – M
Total end play “T
1
”:
0.25 - 0.55 mm (0.0098 - 0.0217 in)
Bearing races:
Refer to
.
SCIA2810E
SCIA5172E
SCIA6529E
ASSEMBLY
AT-391
D
E
F
G
H
I
J
K
L
M
A
B
AT
3.
Install oil pump assembly in transmission case.
CAUTION:
Apply ATF to oil pump bearing.
4.
Apply recommended sealant (Genuine RTV silicone sealant or
equivalent. Refer to
GI-46, "Recommended Chemical Products
.) to oil pump assembly as shown in the figure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc.
from the oil pump mounting bolts and oil pump mounting
bolt mounting surfaces.
5.
Tighten oil pump mounting bolts to specified torque.
CAUTION:
Apply ATF to oil pump bushing.
6.
Install O-ring in input shaft.
CAUTION:
●
Do not reuse O-ring.
●
Apply ATF to O-ring.
7.
Install converter housing in transmission case.
CAUTION:
Do not reuse self-sealing bolt.
SCIA2811E
SCIA5321E
: 48 N·m (4.9 kg-m, 35 ft-lb)
SCIA2300E
SCIA2299E
Converter housing mounting bolt:
: 52 N·m (5.3 kg-m, 38 ft-lb)
Self-sealing bolt:
: 61 N·m (6.2 kg-m, 45 ft-lb)
SCIA4634E
AT-392
ASSEMBLY
8.
Make sure that brake band does not close turbine revolution
sensor hole.
9.
Install A/T fluid temperature sensor 2 in bracket.
10. Install A/T fluid temperature sensor 2 (with bracket) in control
valve assembly.
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve.
11. Install control valve assembly.
a.
Install control valve assembly in transmission case.
SCIA2479E
SCIA5128E
: 7.9 N·m (0.81 kg-m, 70 in-lb)
SCIA5126E
SCIA2315E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст