Infiniti G37 Coupe. Manual — part 829
INSTRUMENT PANEL ASSEMBLY
IP-17
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
24. Disconnect antenna harness connectors (A) and then remove
harness clips.
25. Remove instrument side finisher LH.
• Insert a remover tool into lower space.
• Pull the instrument side finisher LH (1) crosswise.
26. Remove instrument driver lower panel.
• Remove hood opener mounting bolts (A).
Refer to
DLK-211, "HOOD LOCK CONTROL : Removal and
.
• Remove data link connector mounting screws (B).
• Pull back instrument driver lower panel (1).
• Disconnect harness connectors.
27. Remove instrument finisher A.
Pull instrument finisher A (1) upward, and then disengage pawls.
28. Remove instrument side panel LH.
• Remove instrument side panel mounting screw (A).
• Pull the instrument side panel LH (1) crosswise.
: Clip
JMJIA0102GB
: Clip
: Pawl
JMJIA0040GB
: Pawl
: Metal clip
JMJIA0041GB
: Clip
JMJIA0053GB
: Clip
: Pawl
JMJIA0042GB
IP-18
< ON-VEHICLE REPAIR >
INSTRUMENT PANEL ASSEMBLY
29. Remove steering wheel assembly. Refer to
ST-15, "Removal and Installation"
30. Remove steering column covers.
CAUTION:
When removing the column covers, to facilitate the work operation remove first the steering
wheel.
• Remove steering column front lower cover (1).
• Remove cluster lid A lower bracket (2).
• Remove steering column mask (3) and screws.
• Pull up steering column cover upper (4).
• Remove steering column side cover RH (5) (with PADDLE SHIFTER).
• Pull the steering column side cover LH (6) to the left side (with PADDLE SHIFTER).
• Disconnect ADP steering switch connector (with ADP).
• Remove steering column side cover LH (6).
• Remove screws, and then remove steering column lower cover (7).
31. Remove spiral cable and steering angle sensor. Refer to
SR-7, "Removal and Installation"
CAUTION:
Perform 4WAS front actuator adjustment. Refer to
STC-27, "4WAS FRONT ACTUATOR NEUTRAL
POSITION ADJUSTMENT : Description"
.
32. Remove combination switch. Refer to
BCS-80, "Removal and Installation"
33. Remove paddle switch LH/RH (with PADDLE SHIFTER). Refer to
TM-230, "Removal and Installation"
.
34. Remove cluster lid A.
(A)
Column cover (with electric column)
(B)
Column cover (with manual column)
(A)
Column cover (with PADDLE SHIFTER)
(B)
Column cover (without PADDLE SHIFTER)
: Pawl
JMJIA0047GB
JMJIA0048GB
INSTRUMENT PANEL ASSEMBLY
IP-19
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
• Remove knee protector mounting bolts (A) with power tool,
and then remove knee protector (1).
• Disengage harness cover mounting pawl (B) by using tool (A)
located under the column shaft.
• Pull down harness cover (1).
(with harness cover)
• Remove cluster lid A (combination meter) mounting bolts (A).
• Disconnect push button ignition switch harness connector (A).
• Pull back cluster lid A, and disconnect combination meter connectors.
JMJIA0064GB
JMJIA0049GB
JMJIA0050GB
JMJIA0051GB
IP-20
< ON-VEHICLE REPAIR >
INSTRUMENT PANEL ASSEMBLY
35. Remove meter bracket mounting bolts (A), and then remove
meter bracket (1).
36. Remove defroster grille LH. Refer to
VTL-45, "FRONT DEFROSTER NOZZLE, SIDE DEFROSTER NOZ-
ZLE AND VENTILATOR DUCT : Exploded View"
.
• Pull upward, disengage pawls.
• Disconnect harness connector.
37. Remove defroster grille RH. Refer to
VTL-45, "FRONT DEFROSTER NOZZLE, SIDE DEFROSTER NOZ-
ZLE AND VENTILATOR DUCT : Exploded View"
.
• Pull upward, disengaged pawls.
• Disconnect harness connector.
38. Remove body side welt RH. Refer to
INT-14, "Removal and Installation"
39. Remove front pillar garnish RH. Refer to
INT-14, "Removal and Installation"
.
40. Remove instrument side finisher RH.
• Insert a remover tool into lower space.
• Pull the instrument side finisher RH (1) crosswise.
41. Remove instrument passenger lower cover.
• Pull downward, disengaged pawls.
• Pull back instrument passenger lower cover (1).
42. Remove glove box assembly.
• Open the glove box.
JMJIA0052GB
: Clip
: Pawl
JMJIA0054GB
: Pawl
JMJIA0055GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст