Infiniti G37 Coupe. Manual — part 1068
RSU-22
< ON-VEHICLE REPAIR >
REAR STABILIZER
Removal and Installation
INFOID:0000000001671767
REMOVAL
1.
Remove mounting bracket of center muffler and remove mounting rubber of main muffler. Refer to
2.
Remove lower side mounting nuts on stabilizer connecting rod and remove stabilizer connecting rod from
stabilizer bar with power tool.
3.
Remove mounting nuts on stabilizer clamp and remove stabilizer bar with power tool.
INSTALLATION
Install in the reverse order of removal.
Inspection
INFOID:0000000001671768
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer connecting rod, stabilizer bushing and stabilizer clamp for deformation, cracks
or damage. Replace it if a malfunction is detected.
7.
Suspension member
8.
Stabilizer bar
9.
Stabilizer bushing
10. Stabilizer clamp
11. Upper seat
12. Coil spring
13. Ball seat
14. Rubber seat
15. Rear lower link
16. Front lower link
17. Radius rod
18. Cotter pin
19. Axle assembly
20. Shock absorber
21. Bound bumper cover
22. Shock absorber mounting bracket
23. Mounting seal
24. Cap
Refer to
for symbols in the figure.
REAR SUSPENSION MEMBER
RSU-23
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR SUSPENSION MEMBER
Exploded View
INFOID:0000000001686612
1.
Suspension arm
2.
Stopper rubber
3.
Stabilizer connecting rod mounting
bracket
4.
Stabilizer connecting rod
5.
Mount stopper
6.
Damper assembly
JPEIB0059ZZ
RSU-24
< ON-VEHICLE REPAIR >
REAR SUSPENSION MEMBER
Removal and Installation
INFOID:0000000001671770
REMOVAL
1.
Remove tires from vehicle with power tool.
2.
Remove brake caliper with power tool. Hang it in a place where it will not interfere with work. Refer to
56, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Exploded View"
CALIPER ASSEMBLY (2 PISTON TYPE) : Exploded View"
(2 piston type).
CAUTION:
Avoid depressing brake pedal while brake caliper is removed.
3.
Put matching marks on both disc rotor and the wheel hub and bearing assembly, and then remove disc
rotor. Refer to
BR-56, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal and Installation"
(1
piston type),
BR-60, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal and Installation"
(2 pis-
ton type).
4.
Remove wheel sensor and sensor harness from axle assembly and suspension arm. Refer to
5.
Remove height sensor harness from rear suspension member. Refer to
6.
Remove center muffler and main muffler. Refer to
7.
Remove stabilizer bar. Refer to
8.
Remove drive shaft. Refer to
.
9.
Remove propeller shaft. Refer to
models).
10. Remove harness from rear final drive and rear suspension member.
11. Remove final drive. Refer to
(without LSD A/T models),
(with LSD A/T models).
12. Remove parking brake cable mounting bolt and separate parking brake cable from vehicle and rear sus-
pension member. Refer to
PB-7, "PEDAL TYPE : Exploded View"
(pedal type),
(lever type).
13. Remove mounting bolts in lower side of shock absorber.
14. Remove rear lower link and coil spring. Refer to
15. Set suitable jack under rear suspension member.
16. Remove mounting nuts rear suspension member.
17. Slowly lower jack, then remove rear suspension member, suspension arm, radius rod, front lower link and
axle from vehicle as a unit.
18. Remove mounting bolts and nuts, then remove suspension arm, front lower link, and radius rod from rear
suspension member.
INSTALLATION
Note the following, and install in the reverse order of the removal.
• Perform the final tightening of each of parts under unladen conditions, which were removed when removing
rear suspension assembly.
• Check wheel sensor harness for proper connection. Refer to
.
Inspection
INFOID:0000000001671771
INSPECTION AFTER REMOVAL
Check front suspension member for deformation, cracks, or any other damage. Replace if necessary.
INSPECTION AFTER INSTALLATION
7.
Suspension member
8.
Stabilizer bar
9.
Stabilizer bushing
10. Stabilizer clamp
11. Upper seat
12. Coil spring
13. Ball seat
14. Rubber seat
15. Rear lower link
16. Front lower link
17. Radius rod
18. Cotter pin
19. Axle assembly
20. Shock absorber
21. Bound bumper cover
22. Shock absorber mounting bracket
23. Mounting seal
24. Cap
Refer to
for symbols in the figure.
REAR SUSPENSION MEMBER
RSU-25
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
• Check wheel alignment. Refer to
• Adjust neutral position of steering angle sensor after checking wheel alignment. Refer to
MENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
• Adjust parking brake operation (stroke).
PB-3, "PEDAL TYPE : Inspection and Adjustment"
(pedal type),
4, "LEVER TYPE : Inspection and Adjustment"
(lever type).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст