Infiniti G37 Coupe. Manual — part 1067
RSU-18
< ON-VEHICLE REPAIR >
RADIUS ROD
Removal and Installation
INFOID:0000000001671761
REMOVAL
1.
Remove tire with power tool.
2.
Set suitable jack under axle assembly.
3.
Remove mounting bolts and nuts in axle side of radius rod with power tool.
4.
Remove mounting bolt in rear suspension member side of radius rod with power tool, then remove radius
rod.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of rear suspension member and axle installation position (rubber bushing), under
unladen conditions with tires on level ground.
Inspection
INFOID:0000000001671762
INSPECTION AFTER REMOVAL
Check radius rod and bushing for any deformation, cracks, or damage. Replace if there are.
INSPECTION AFTER INSTALLATION
• Check wheel alignment. Refer to
• Adjust neutral position of steering angle sensor after checking the wheel alignment. Refer to
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
7.
Suspension member
8.
Stabilizer bar
9.
Stabilizer bushing
10. Stabilizer clamp
11. Upper seat
12. Coil spring
13. Ball seat
14. Rubber seat
15. Rear lower link
16. Front lower link
17. Radius rod
18. Cotter pin
19. Axle assembly
20. Shock absorber
21. Bound bumper cover
22. Shock absorber mounting bracket
23. Mounting seal
24. Cap
Refer to
for symbols in the figure.
FRONT LOWER LINK
RSU-19
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
FRONT LOWER LINK
Exploded View
INFOID:0000000001686610
1.
Suspension arm
2.
Stopper rubber
3.
Stabilizer connecting rod mounting
bracket
4.
Stabilizer connecting rod
5.
Mount stopper
6.
Damper assembly
JPEIB0059ZZ
RSU-20
< ON-VEHICLE REPAIR >
FRONT LOWER LINK
Removal and Installation
INFOID:0000000001671764
REMOVAL
1.
Remove tire with power tool.
2.
Set suitable jack under axle assembly to relieve the coil spring tension.
3.
Remove mounting bolts and nuts between front lower link and rear suspension member with power tool.
4.
Remove mounting bolts and nuts between front lower link and axle with power tool.
5.
Remove front lower link.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of rear suspension member and axle installation position (rubber bushing), under
unladen conditions with tires on level ground.
Inspection
INFOID:0000000001671765
INSPECTION AFTER REMOVAL
Check front lower link and bushing for any deformation, cracks, or damage. Replace if there are.
INSPECTION AFTER INSTALLATION
• Check wheel alignment. Refer to
• Adjust neutral position of steering angle sensor after checking the wheel alignment. Refer to
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
7.
Suspension member
8.
Stabilizer bar
9.
Stabilizer bushing
10. Stabilizer clamp
11. Upper seat
12. Coil spring
13. Ball seat
14. Rubber seat
15. Rear lower link
16. Front lower link
17. Radius rod
18. Cotter pin
19. Axle assembly
20. Shock absorber
21. Bound bumper cover
22. Shock absorber mounting bracket
23. Mounting seal
24. Cap
Refer to
for symbols in the figure.
REAR STABILIZER
RSU-21
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR STABILIZER
Exploded View
INFOID:0000000001686611
1.
Suspension arm
2.
Stopper rubber
3.
Stabilizer connecting rod mounting
bracket
4.
Stabilizer connecting rod
5.
Mount stopper
6.
Damper assembly
JPEIB0059ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст