Infiniti G37 Coupe. Manual — part 1069
RSU-26
< REMOVAL AND INSTALLATION >
REAR SUSPENSION ASSEMBLY
REMOVAL AND INSTALLATION
REAR SUSPENSION ASSEMBLY
Exploded View
INFOID:0000000001671772
JPEIB0059ZZ
REAR SUSPENSION ASSEMBLY
RSU-27
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
Removal and Installation
INFOID:0000000001671773
REMOVAL
1.
Remove tire with power tool.
2.
Remove brake caliper with power tool. Hang it in a place where it will not interfere with work. Refer to
56, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Exploded View"
CALIPER ASSEMBLY (2 PISTON TYPE) : Exploded View"
CAUTION:
Never depressing brake pedal while brake caliper is removed.
3.
Put matching marks on both disc rotor and the wheel hub and bearing assembly, and then remove disc
rotor. Refer to
BR-56, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal and Installation"
(1
piston type),
BR-60, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal and Installation"
(2 pis-
ton type).
4.
Remove wheel sensor from rear final drive. Refer to
5.
Remove height sensor harness from rear suspension member. Refer to
6.
Remove harness from rear final drive and rear suspension member.
7.
Remove center muffler. Refer to
8.
Remove rear propeller shaft. Refer to
(M/T models),
(A/T models).
9.
Separate parking brake cable from vehicle and rear suspension member. Refer to
(pedal type),
PB-8, "LEVER TYPE : Exploded View"
(lever type).
10. Remove rear lower link and coil spring. Refer to
11. Remove mounting bolt on lower side of shock absorber. Refer to
.
12. Set suitable jack under rear final drive.
13. Gradually lowering jack, remove rear suspension assembly.
CAUTION:
Secure suspension assembly to a suitable jack while removing it.
INSTALLATION
Note the following, and install in the reverse order of the removal.
• Perform the final tightening of each of parts under unladen conditions, with tires on level ground.
• Check wheel sensor harness for proper connection. Refer to
.
Inspection
INFOID:0000000001671774
INSPECTION AFTER REMOVAL
• Check the wheel alignment. Refer to
• Adjust neutral position of steering angle sensor after checking the wheel alignment. Refer to
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
• Adjust parking brake operation. Refer to
PB-3, "PEDAL TYPE : Inspection and Adjustment"
PB-4, "LEVER TYPE : Inspection and Adjustment"
(lever type).
1.
Suspension arm
2.
Stopper rubber
3.
Stabilizer connecting rod mounting
bracket
4.
Stabilizer connecting rod
5.
Mount stopper
6.
Damper assembly
7.
Suspension member
8.
Stabilizer bar
9.
Stabilizer bushing
10. Stabilizer clamp
11. Upper seat
12. Coil spring
13. Ball seat
14. Rubber seat
15. Rear lower link
16. Front lower link
17. Radius rod
18. Cotter pin
19. Axle assembly
20. Shock absorber
21. Bound bumper cover
22. Shock absorber mounting bracket
23. Mounting seal
24. Cap
for symbols in the figure.
RSU-28
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Alignment
INFOID:0000000001671775
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Ball Joint
INFOID:0000000001671776
Wheel Height
INFOID:0000000001671777
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Applied model
Except for sport models
For sport models
Camber
Degree minute (Decimal degree)
Minimum
–1
°
50
′
(–1.83
°
)
Nominal
–1
°
20
′
(–1.33
°
)
Maximum
–0
°
50
′
(–0.83
°
)
Total toe-in
Distance
Minimum
0 mm (0 in)
0 mm (0 in)
Nominal
In 2.9 mm (0.110 in)
In 2.8 mm (0.110 in)
Maximum
In 5.8 mm (0.220 in)
In 5.6 mm (0.220 in)
Angle (left wheel or right wheel)
Degree minute (Decimal degree)
Minimum
0
°
00
′
(0.00
°
)
Nominal
In 0
°
07
′
(0.12
°
)
Maximum
In 0
°
14
′
(0.23
°
)
Swing torque
0.5 – 3.4 N·m (0.06 – 0.34 kg-m, 5 – 30 in-lb)
Measurement on spring balance (cotter pinhole position)
8.1 – 54.8 N (0.83 – 5.6 kg, 1.82 – 12.32 lb)
Rotating torque
0.5 – 3.4 N·m (0.06 – 0.34 kg-m, 5 – 30 in-lb)
Axial end play
0 mm (0 in)
Applied model
Except for sport models
For sport models
Tire
225/50R18
245/40R19
Rear (Hr)
702 mm (27.64 in)
705 mm (27.76 in)
SFA818A
SB-1
RESTRAINTS
C
D
E
F
G
I
J
K
L
M
SECTION
SB
A
B
SB
N
O
P
CONTENTS
SEAT BELT
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Seat Belt Service . . . . . . . ...
ON-VEHICLE REPAIR . . . . . . . . ..
FRONT SEAT BELT . . . . . . . . . . .
SEAT BELT RETRACTOR . . . . . . . . . . ..
SEAT BELT RETRACTOR : Inspection . . . . ....
SEAT BELT RETRACTOR : Exploded View . . .....
SEAT BELT RETRACTOR : Removal and Instal-
lation . . . . . . . . . . . . . . . . . . ..
SEAT BELT BUCKLE . . . . . . . . . . . .....
SEAT BELT BUCKLE : Inspection . . . . . . ....
SEAT BELT BUCKLE : Exploded View . . . . .....
SEAT BELT BUCKLE : Removal and Installation . ..
REAR SEAT BELT . . . . . . . . . . . .
SEAT BELT RETRACTOR . . . . . . . . . . .
SEAT BELT RETRACTOR : Inspection . . . . ...
SEAT BELT RETRACTOR : Exploded View . . ...
SEAT BELT RETRACTOR : Removal and Instal-
lation . . . . . . . . . . . . . . . . . .
SEAT BELT BUCKLE . . . . . . . . . . . .
SEAT BELT BUCKLE : Inspection . . . . . . ..
SEAT BELT BUCKLE : Exploded View . . . . ...
SEAT BELT BUCKLE : Removal and Installation .
LATCH SYSTEM FOR CHILDREN . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
TOP TETHER STRAP CHILD RESTRAINT . .
Exploded View . . . . . . . . . . . . . . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст