Infiniti G37 Coupe. Manual — part 822
FLOOR TRIM
INT-19
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
FLOOR TRIM
Exploded View
INFOID:0000000001722847
Removal and Installation
INFOID:0000000001722848
REMOVAL
1.
Remove front seat (LH/RH). Refer to
SE-152, "Removal and Installation"
2.
Remove rear seat cushion. Refer to
SE-160, "Removal and Installation"
.
3.
Remove accelerator pedal pad. Refer to
ACC-3, "Removal and Installation"
.
4.
Disengage clip of floor hook (1) with remover tool (A).
5.
Remove foot grille. Refer to
VTL-48, "FOOT GRILLE : Removal and Installation"
.
1.
Floor hook
2.
Floor trim
3.
Fixing clip
4.
Rear floor spacer (RH)
5.
Rear floor spacer (LH)
6.
Front floor spacer (LH)
7.
Front floor spacer (RH)
8.
Footrest
JMJIA0968ZZ
: Clip
JMJIA0092GB
INT-20
< ON-VEHICLE REPAIR >
FLOOR TRIM
6.
Remove front seat belt floor anchor bolt (LH/RH). Refer to
SB-5, "SEAT BELT RETRACTOR : Removal
7.
Remove center console assembly. Refer to
IP-24, "Removal and Installation"
8.
Remove instrument lower cover, instrument driver panel, instrument assist lower panel and instrument
side panel (LH/RH). Refer to
IP-12, "Removal and Installation"
.
9.
Remove G-sensor (1).
Refer to
BRC-104, "Removal and Installation"
.
10. Remove diagnosis sensor unit (2).
SR-16, "Removal and Installation"
.
11. Remove console rear bracket (3).
.
12. Remove floor harness mounting clamps (A).
13. Remove dash side finisher (LH/RH), front kicking plate inner (LH/RH) and body side welt (LH/RH).
INT-14, "Removal and Installation"
14. Remove floor trim mounting clips and fixing nuts.
15. Remove floor trim from floor trim fixing clips (A) and remove floor
carpet (1).
INSTALLATION
Install in the reverse order of removal.
JMJIA0093GB
JMJIA0094GB
HEADLINING
INT-21
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
HEADLINING
NORMAL ROOF
NORMAL ROOF : Exploded View
INFOID:0000000001722849
NORMAL ROOF : Removal and Installation
INFOID:0000000001722850
REMOVAL
1.
Remove front pillar garnish (LH/RH) and body side welt (LH/RH).
Refer to
INT-14, "Removal and Installation"
1.
Sun visor holder
2.
Sun visor cover
3.
Sun visor assembly
4.
Roof front finisher
5.
Assist grip
6.
Headlining assembly
7.
Rear hidden clip
8.
Antenna feeder
9.
Over head console
10. Map lamp assembly
11. Dual lock fastener
12. Roof harness
13. Roof bracket
14. Roof plate assembly
15. Map lamp lens
16. Assist grip clip
: Pawl
: Metal clip
JMJIA0969ZZ
INT-22
< ON-VEHICLE REPAIR >
HEADLINING
2.
Remove antenna feeder securing clips with a remover tool after
removing front pillar garnish (LH), then disconnect antenna
feeder connectors (A).
3.
Remove front roof finisher mounting metal clips and pawls, and
then remove front roof finisher (1).
4.
Remove sun visor assembly (LH/RH).
• Remove sun visor cover.
• Remove sun visor assembly mounting screws.
• Disconnect vanity mirror lamp harness connectors.
5.
Rotate 45 degrees and remove sun visor holder (1) (LH/RH).
6.
Remove mounting plastic clips (A) using a screwdriver (B) of
front and rear assistance grips (1), and then remove assist grips.
7.
Remove rear seat cushion and seatback. Refer to
SE-160, "Removal and Installation"
8.
Remove front kicking plate inner (LH/RH), rear side finisher (LH/RH), rear pillar finisher (LH/RH).
Refer to
INT-14, "Removal and Installation"
: Clip
JMJIA0101GB
: Pawl
: Metal clip
JMJIA0097GB
JMJIA0098GB
JMJIA0096GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст