Infiniti FX35, FX50 (S51). Manual — part 1014
EXL-52
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
B2514 HEIGHT SENSOR UNUSUAL [RR]
Is the measurement value within the standard value?
YES
>> GO TO 7.
NO
>> Replace AFS control unit.
7.
CHECK HEIGHT SENSOR GROUND CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect AFS control unit connector and the height sensor connector.
3.
Check continuity between the AFS control unit harness connector and the height sensor harness connec-
tor.
Does continuity exist?
YES
>> Replace the height sensor.
NO
>> Repair the harnesses or connectors.
Component Inspection
INFOID:0000000005244701
1.
CHECK HEIGHT SENSOR
1.
Remove the height sensor (the height sensor connector is connected).
2.
Start the engine.
3.
Turn the light switch 2ND.
4.
Select "HI SEN OTP RR” of AFS data monitor item.
5.
With moving the sensor lever, check the monitor status.
Is the output value normal?
YES
>> Height sensor is normal.
NO
>> Replace the height sensor.
Terminals
Voltage
(Approx.)
(+)
(
−
)
AFS control unit
Ground
Connector
Terminal
M16
8
0 V
AFS control unit
Height sensor
Continuity
Connector
Terminal
Connector
Terminal
M16
8
B32
3
Existed
Monitor item
Condition
Monitor status
[Standard value
(Approx.)]
HI SEN OTP RR
Sensor lever po-
sition
Contact with
stopper
0.9 V
Moving be-
tween two posi-
tions
Smooth move-
ment
90
°
from stopper
4.5 V
B2516 SHIFT SIGNAL [P, R]
EXL-53
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
B2516 SHIFT SIGNAL [P, R]
Description
INFOID:0000000005244702
AFS control unit receives the shift position signal from TCM with CAN communication.
DTC Logic
INFOID:0000000005244703
DTC DETECTION LOGIC
[B2516] Shift signal [P, R]
DTC CONFIRMATION PROCEDURE
1.
DTC ERASE
Erase the DTC memory of AFS with CONSULT-III.
>> GO TO 2.
2.
DTC CONFIRMATION
1.
Turn the ignition ON.
2.
Select the self-diagnosis with CONSULT-III.
3.
Check the self-diagnosis result. Refer to
Is “B2516” detected?
YES
>> Refer to
.
NO
>> Refer to
GI-36, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000005244704
1.
TCM SELF-DIAGNOSIS
Check the self-diagnosis result with CONSULT-III. Check that TCM does not detect any DTCs.
Is any DTC detected?
YES
>> Check TCM. Refer to
NO
>> GO TO 2.
2.
DTC ERASE
Erase the DTC memory of AFS with CONSULT-III.
Is the memory erased?
YES
>> Inspection end.
NO
>> Replace AFS control unit.
DTC detection condition
DTC erase condition
Possible causes
The shift position signal is not received.
Ignition switch OFF
• TCM
• AFS control unit
EXL-54
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
B2517 VEHICLE SPEED SIGNAL
B2517 VEHICLE SPEED SIGNAL
Description
INFOID:0000000005244705
AFS control unit receives the vehicle speed signal from the unified meter and A/C amp. with CAN communica-
tion.
DTC Logic
INFOID:0000000005244706
DTC DETECTION LOGIC
[B2517] Vehicle speed signal
DTC CONFIRMATION PROCEDURE
1.
DTC ERASE
Erase the DTC memory of AFS with CONSULT-III.
>> GO TO 2.
2.
DTC CONFIRMATION
1.
Turn the ignition ON.
2.
Select the self-diagnosis with CONSULT-III.
3.
Check the self-diagnosis result. Refer to
Is “B2517” detected?
YES
>> Refer to
.
NO
>> Refer to
GI-36, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000005244707
1.
UNIFIED METER AND A/C AMP. SELF-DIAGNOSIS
Check the self-diagnosis result with CONSULT-III. Check that the unified meter and A/C amp. does not detect
any DTCs.
Is any DTC detected?
YES
>> Check the unified meter and A/C amp. Refer to
NO
>> GO TO 2.
2.
DTC ERASE
Erase the DTC memory of AFS with CONSULT-III.
Is the memory erased?
YES
>> Inspection end.
NO
>> Replace AFS control unit.
DTC detection condition
DTC erase condition
Possible causes
The vehicle speed signal is not received.
Ignition switch OFF
• Unified meter and A/C
amp.
• AFS control unit
B2519 LEVELIZER CALIBRATION
EXL-55
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
B2519 LEVELIZER CALIBRATION
Description
INFOID:0000000005244708
AFS control unit transmits the height sensor signal from the height sensor.
DTC Logic
INFOID:0000000005244709
[B2519] Levelizer calibration
Diagnosis Procedure
INFOID:0000000005244710
1.
LEVELIZER ADJUSTMENT
Perform the levelizer adjustment.
>> Refer to
EXL-7, "LEVELIZER ADJUSTMENT : Special Repair Requirement"
DTC detection condition
DTC erase condition
Possible causes
The height sensor adjustment position is not recognized.
When the levelizer adjust-
ment is completed
AFS control unit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст