Infiniti FX35, FX50 (S51). Manual — part 931
EM-24
< PERIODIC MAINTENANCE >
[VQ35HR]
CAMSHAFT VALVE CLEARANCE
• Thickness of new valve lifter can be identified by stamp marks
on the reverse side (inside the cylinder).
Stamp mark 788 indicates 7.88 mm (0.3102 in) in thickness.
Available thickness of valve lifter: 27 sizes with range 7.88 to 8.40 mm (0.3102 to 0.3307 in) in steps of
0.02 mm (0.0008 in) (when manufactured at factory). Refer to
6.
Install selected valve lifter.
7.
Install camshaft. Refer to
EM-70, "Removal and Installation"
.
8.
Manually turn crankshaft pulley a few turns.
9.
Check that the valve clearances for cold engine are within the specifications by referring to the specified
values.
10. Install all removal parts in the reverse order of removal.
11. Warm up the engine, and check for unusual noise and vibration.
A
: Stamp
B
: Thickness of valve lifter
JPBIA0170ZZ
COMPRESSION PRESSURE
EM-25
< PERIODIC MAINTENANCE >
[VQ35HR]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
COMPRESSION PRESSURE
Inspection
INFOID:0000000005245122
1.
Warm up engine thoroughly. Then, stop it.
2.
Release fuel pressure. Refer to
.
3.
Disconnect fuel pump fuse (1) from IPDM E/R (2) to avoid fuel
injection during measurement.
4.
Remove engine cover with power tool. Refer to
.
5.
Remove ignition coil and spark plug from each cylinder. Refer to
6.
Connect engine tachometer (not required in use of CONSULT-III).
7.
Install compression gauge with an adapter (commercial service
tool) onto spark plug hole.
• Use the adapter hat has a smaller than 20 mm (0.79 in) (a) as
shown in the figure. Otherwise, it may be caught by cylinder
head during removal.
8.
With accelerator pedal fully depressed, turn ignition switch to “START” for cranking. When the gauge
pointer stabilizes, read the compression pressure and the engine rpm. Perform these steps to check each
cylinder.
CAUTION:
Always use a fully charged battery to obtain the specified engine speed.
• If the engine speed is out of the specified range, check battery liquid for proper gravity. Check the
engine speed again with normal battery gravity. Refer to
• If compression pressure is below minimum value, check valve clearances and parts associated with
combustion chamber (valve, valve seat, piston, piston ring, cylinder bore, cylinder head, cylinder head
gasket). After the checking, measure compression pressure again.
JMBIA1506ZZ
PBIC0900E
a
: 20 mm (0.79 in)
JPBIA0171ZZ
Compression pressure
: Refer to
EM-26
< PERIODIC MAINTENANCE >
[VQ35HR]
COMPRESSION PRESSURE
• If some cylinder has low compression pressure, pour small amount of engine oil into the spark plug hole
of the cylinder to re-check it for compression.
- If the added engine oil improves the compression, piston rings may be worn out or damaged. Check pis-
ton rings and replace if necessary.
- If the compression pressure remains at low level despite the addition of engine oil, valves may be mal-
functioning. Check valves for damage. Replace valve or valve seat accordingly.
• If two adjacent cylinders have respectively low compression pressure and their compression remains
low even after the addition of engine oil, cylinder head gaskets are leaking. In such a case, replace cyl-
inder head gaskets.
9.
After inspection is completed, install removed parts.
10. Start the engine, and check that the engine runs smoothly.
11. Perform trouble diagnosis. If DTC appears, erase it. Refer to
ENGINE COVER
EM-27
< REMOVAL AND INSTALLATION >
[VQ35HR]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
REMOVAL AND INSTALLATION
ENGINE COVER
Exploded View
INFOID:0000000005245123
Removal and Installation
INFOID:0000000005245124
REMOVAL
Loosen mounting bolts and nuts in the reverse order as shown in the
figure, and then remove engine cover.
CAUTION:
Never damage or scratch engine cover when installing or
removing.
INSTALLATION
Install engine cover, and then tighten mounting bolts and nuts in
numerical order as shown in the figure.
CAUTION:
Never damage or scratch engine cover when installing or
removing.
1
: Engine cover
for symbols in the figure.
JPBIA0256GB
JPBIA1823ZZ
JPBIA1823ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст