Infiniti FX35, FX50 (S51). Manual — part 1886
A/T SHIFT SELECTOR
TM-351
< REMOVAL AND INSTALLATION >
[7AT: RE7R01B (VK50VE)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Removal and Installation
INFOID:0000000005250349
REMOVAL
1.
Shift the selector lever to “P” position.
2.
Remove control rod from A/T shift selector.
3.
Shift the selector lever to “N” position.
4.
Remove knob cover (A) below selector lever downward.
5.
Pull lock pin (1) out of selector lever knob (2).
6.
Remove selector lever knob.
7.
Remove center console assembly. Refer to
.
CAUTION:
When disconnecting selector lever position indicator con-
nector from shift position switch, never twist or apply an
excessive load to the connector.
8.
Remove the rear ventilator duct 1. Refer to
.
9.
Disconnect A/T shift selector connector.
10. Remove harness clips from A/T shift selector assembly.
11. Shift the selector lever to “P” position.
12. Remove A/T shift selector assembly mounting bolts.
13. Slightly lift the A/T shift selector assembly (1) and slide it right-
ward. Then pull it out in the diagonally right direction.
14. Remove adapter from A/T shift selector assembly.
15. Remove dust cover and dust cover plate from A/T shift selector
assembly.
16. Remove dust cover from dust cover plate.
17. Remove shift lock unit from A/T shift selector assembly.
18. Remove brackets from vehicle floor panel.
19. Remove selector lever position indicator from console finisher
assembly:
a.
Remove indicator assembly from console finisher assembly.
Refer to
.
b.
Remove insert finisher from indicator assembly.
c.
Remove selector lever position indicator.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Apply multi-purpose grease on the pin surface (that slides after installing a collar) of the pivot pin.
• Refer to the followings when installing selector lever knob to A/T shift selector assembly.
1.
Insert lock pin to selector lever knob.
2.
Install selector lever knob over selector lever until a click is felt.
1.
Selector lever knob
2.
Lock pin
3.
Indicator plate
4.
Selector lever position indicator
5.
Harness connector
6.
Insert finisher
7.
Control rod
8.
Dust cover
9.
Bracket
10.
Dust cover plate
11.
Snap pin
12.
Washer
13.
Collar
14.
Clip
15.
Pivot pin
16.
Insulator
17.
Shift lock unit
18.
A/T shift selector assembly
19.
Adapter
: Apply multi-purpose grease.
Refer to
for symbols not described on the above.
JPDIA0898ZZ
JPDIA0055ZZ
TM-352
< REMOVAL AND INSTALLATION >
[7AT: RE7R01B (VK50VE)]
A/T SHIFT SELECTOR
CAUTION:
• Install it straight, and never tap or apply any shock to install it.
• Never push selector button.
• When installing control rod to A/T shift selector assembly, refer to “ADJUSTMENT”. Refer to
.
Inspection and Adjustment
INFOID:0000000005250350
INSPECTION AFTER INSTALLATION
Check A/T positions after adjusting A/T positions. Refer to
TM-349, "Inspection and Adjustment"
ADJUSTMENT AFTER INSTALLATION
Adjust A/T positions. Refer to
CONTROL ROD
TM-353
< REMOVAL AND INSTALLATION >
[7AT: RE7R01B (VK50VE)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CONTROL ROD
Exploded View
INFOID:0000000005250351
Removal and Installation
INFOID:0000000005250352
REMOVAL
1.
Shift the selector lever to “P” position.
2.
Disconnect A/T shift selector and control rod. Refer to
.
3.
Remove manual lever from A/T assembly.
4.
Remove control rod from manual lever.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Apply multi-purpose grease on the pin surface (that slides after installing collar) of the tip of the con-
trol rod.
• When installing control rod to A/T shift selector assembly, refer to “ADJUSTMENT”. Refer to
.
Inspection
INFOID:0000000005250353
INSPECTION AFTER INSTALLATION
Check A/T positions after adjusting A/T positions. Refer to
TM-349, "Inspection and Adjustment"
ADJUSTMENT AFTER INSTALLATION
Adjust A/T positions. Refer to
TM-349, "Inspection and Adjustment"
1.
A/T assembly
2.
Manual lever
3.
Lock washer
4.
Control rod
5.
Washer
6.
Insulator
7.
Collar
8.
Conical washer
9.
Snap pin
: Apply multi-purpose grease.
for symbols not described on the above.
JSDIA1002GB
TM-354
< REMOVAL AND INSTALLATION >
[7AT: RE7R01B (VK50VE)]
PADDLE SHIFTER
PADDLE SHIFTER
Exploded View
INFOID:0000000005250354
Removal and Installation
INFOID:0000000005250355
REMOVAL
1.
Remove steering column cover. Refer to
.
2.
Disconnect paddle shifter connectors from each paddle shifter.
3.
Remove paddle shifter mounting bolts and nuts.
4.
Remove each paddle shifter from steering column assembly.
INSTALLATION
Install in the reverse order of removal.
1.
Steering column assembly
2.
Paddle shifter (shift-down)
3.
Paddle shifter (shift-up)
Refer to
for symbols in the figure.
JPDIA0051GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст