Infiniti FX35, FX50 (S51). Manual — part 1838
PREPARATION
TM-159
< PREPARATION >
[7AT: RE7R01A (VQ35HR)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000005250144
*: Always check with the Parts Department for the latest parts information.
Tool number
Tool name
Description
1.
315268E000*
O-ring
2.
310811EA5A*
Charging pipe
A/T fluid changing and adjustment
Power tool
Loosening bolts and nuts
JSDIA1332ZZ
PBIC0190E
TM-160
< PERIODIC MAINTENANCE >
[7AT: RE7R01A (VQ35HR)]
A/T FLUID
PERIODIC MAINTENANCE
A/T FLUID
Changing
INFOID:0000000005250145
CAUTION:
• Use only Genuine NISSAN Matic S ATF. Never mix with other ATF.
• Using ATF other than Genuine NISSAN Matic S ATF will cause deterioration in driveability and A/T
durability, and may damage the A/T, which is not covered by the INFINITI new vehicle limited war-
ranty.
• When filling ATF, be careful not to scatter heat generating parts such as exhaust.
1.
Step 1
a.
Install the O-ring (315268E000) (A) to the charging pipe
(310811EA5A) (B).
2.
Step 2
a.
Use CONSULT-III to check that the ATF temperature is 40
°
C (104
°
F) or less.
b.
Lift up the vehicle.
c.
Remove the drain plug from the oil pan, and then drain the ATF.
d.
When the ATF starts to drip, temporarily tighten the drain plug to the oil pan.
NOTE:
Never replace drain plug and drain plug gasket with new ones yet.
e.
Remove overflow plug from oil pan.
f.
Install the charging pipe (A) to the overflow plug hole.
CAUTION:
Tighten the charging pipe by hand.
g.
Install the bucket pump hose (B) to the charging pipe.
CAUTION:
Insert the bucket pump hose all the way to the end of the
charging pipe.
h.
Fill approximately 3 liters (3-1/8 US qt, 2-5/8 lmp qt) of the ATF.
i.
Remove the bucket pump hose to remove the charging pipe,
and then temporarily tighten the overflow plug to the oil pan.
CAUTION:
Quickly perform the procedure to avoid ATF leakage from
the oil pan.
j.
Lift down the vehicle.
k.
Start the engine and wait for approximately 3 minutes.
l.
Stop the engine.
3.
Step 3
a.
Repeat “Step 2”.
4.
Final Step
ATF
: Refer to
TM-187, "General Specification"
Fluid capacity
: Refer to
TM-187, "General Specification"
JSDIA1334ZZ
JSDIA1335ZZ
A/T FLUID
TM-161
< PERIODIC MAINTENANCE >
[7AT: RE7R01A (VQ35HR)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
a.
Use CONSULT-III to check that the ATF temperature is 40
°
C (104
°
F) or less.
b.
Lift up the vehicle.
c.
Remove the drain plug from the oil pan, and then drain the ATF.
d.
When the ATF starts to drip, tighten the drain plug to the oil pan to the specified torque. Refer to
CAUTION:
Never reuse drain plug and drain plug gasket.
e.
Remove overflow plug from oil pan.
f.
Install the charging pipe (A) to the overflow plug hole.
CAUTION:
Tighten the charging pipe by hand.
g.
Install the bucket pump hose (B) to the charging pipe.
CAUTION:
Insert the bucket pump hose all the way to the end of the
charging pipe.
h.
Fill approximately 3 liters (3-1/8 US qt, 2-5/8 lmp qt) of the ATF.
i.
Remove the bucket pump hose to remove the charging pipe,
and then temporarily tighten the overflow plug to the oil pan.
CAUTION:
Quickly perform the procedure to avoid ATF leakage from
the oil pan.
j.
Lift down the vehicle.
k.
Start the engine.
l.
Make the ATF temperature approximately 40
°
C (104
°
F).
NOTE:
The ATF level is greatly affected by the temperature. Always check the ATF temperature on “ATF TEMP
1” of “Data Monitor” using CONSULT-III.
m. Park vehicle on level surface and set parking brake.
n.
Shift the selector lever through each gear position. Leave selector lever in “P” position.
o.
Lift up the vehicle when the ATF temperature reaches 40
°
C (104
°
F), and then remove the overflow plug
from the oil pan.
p.
When the ATF starts to drip, tighten the overflow plug to the oil pan to the specified torque. Refer to
CAUTION:
Never reuse overflow plug.
Adjustment
INFOID:0000000005250146
CAUTION:
• Use only Genuine NISSAN Matic S ATF. Never mix with other ATF.
• Using ATF other than Genuine NISSAN Matic S ATF will cause deterioration in driveability and A/T
durability, and may damage the A/T, which is not covered by the INFINITI new vehicle limited war-
ranty.
• When filling ATF, be careful not to scatter heat generating parts such as exhaust.
• Always maintain the ATF temperature within between 35
°
C (95
°
F) and 45
°
C (113
°
F) while checking
with CONSULT-III when the ATF level adjustment is performed.
JSDIA1335ZZ
ATF
: Refer to
TM-187, "General Specification"
Fluid capacity
: Refer to
TM-162
< PERIODIC MAINTENANCE >
[7AT: RE7R01A (VQ35HR)]
A/T FLUID
1.
Install the O-ring (315268E000) (A) to the charging pipe
(310811EA5A) (B).
2.
Start the engine.
3.
Make the ATF temperature approximately 40
°
C (104
°
F).
NOTE:
The ATF level is greatly affected by the temperature. Always
check the ATF temperature on “ATF TEMP 1” of “Data Monitor”
using CONSULT-III.
4.
Park vehicle on level surface and set parking brake.
5.
Shift the selector lever through each gear position. Leave selec-
tor lever in “P” position.
6.
Lift up the vehicle.
7.
Check the ATF leakage from transmission.
8.
Remove overflow plug from oil pan.
9.
Install the charging pipe (A) to the overflow plug hole.
CAUTION:
Tighten the charging pipe by hand.
10. Install the bucket pump hose (B) to the charging pipe.
CAUTION:
Insert the bucket pump hose all the way to the end of the
charging pipe.
11. Fill approximately 0.5 liters (1/2 US qt, 1/2 lmp qt) of the ATF.
12. Check that the ATF leaks when removing the charging pipe and
the bucket pump hose. If the ATF does not leak, refill the ATF.
13. When the ATF starts to drip, tighten the overflow plug to the oil
pan to the specified torque. Refer to
.
CAUTION:
Never reuse overflow plug.
JSDIA1334ZZ
JSDIA1335ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст