Infiniti FX35, FX50 (S51). Manual — part 1367
MA-32
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
• Check the propeller shaft tube surface for dents or cracks. If damaged, replace propeller shaft assembly.
• If center bearing is noisy or damaged, replace propeller shaft assembly.
VIBRATION
If vibration is present at high speed, inspect propeller shaft runout first.
1.
With a dial indicator, measure propeller shaft runout at runout
measuring points by rotating final drive companion flange with
hands.
2.
If runout still exceeds specifications, separate propeller shaft at
final drive companion flange; then rotate companion flange 120,
240 degrees and install propeller shaft.
3.
Check runout again. If runout still exceeds specifications,
replace propeller shaft assembly.
4.
Check the vibration by driving vehicle.
RUNOUT MEASURING POINT
Propeller shaft runout measuring point (Point “ ”).
REAR PROPELLER SHAFT: 3F80A-1VL107
REAR PROPELLER SHAFT: 3F80A-1VL107 : Inspection
INFOID:0000000005248749
NOISE
• Check the propeller shaft tube surface for dents or cracks. If damaged, replace propeller shaft assembly.
• If center bearing is noisy or damaged, replace propeller shaft assembly.
VIBRATION
If vibration is present at high speed, inspect propeller shaft runout first.
1.
With a dial indicator, measure propeller shaft runout at runout
measuring points by rotating final drive companion flange with
hands.
2.
If runout still exceeds specifications, separate propeller shaft at
final drive companion flange, then rotate companion flange 60,
120, 180, 240, 300 degrees and install propeller shaft.
3.
Check runout again. If runout still exceeds specifications,
replace propeller shaft assembly.
4.
Check the vibration by driving vehicle.
RUNOUT MEASURING POINT
Limit
Propeller shaft runout
: Refer to
.
SDIA1087E
: Vehicle front
Standard
A
: 192 mm (7.56 in)
B
: 172 mm (6.77 in)
C
: 172 mm (6.77 in)
JSDIA0169ZZ
Limit
Propeller shaft runout
: Refer to
.
SDIA1087E
CHASSIS MAINTENANCE
MA-33
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
Propeller shaft runout measuring point (Point “ ”).
REAR PROPELLER SHAFT: 3F-R-2VL107
REAR PROPELLER SHAFT: 3F-R-2VL107 : Inspection
INFOID:0000000005248750
NOISE
• Check the propeller shaft tube surface for dents or cracks. If damaged, replace propeller shaft assembly.
• If center bearing is noisy or damaged, replace propeller shaft assembly.
VIBRATION
If vibration is present at high speed, inspect propeller shaft runout first.
1.
With a dial indicator, measure propeller shaft runout at runout
measuring points by rotating final drive companion flange with
hands.
2.
If runout still exceeds specifications, separate propeller shaft at
final drive companion flange, then rotate companion flange 60,
120, 180, 240, 300 degrees and install propeller shaft.
3.
Check runout again. If runout still exceeds specifications,
replace propeller shaft assembly.
4.
Check the vibration by driving vehicle.
RUNOUT MEASURING POINT
Propeller shaft runout measuring point (Point “ ”).
FRONT DIFFERENTIAL GEAR OIL: F160A
FRONT DIFFERENTIAL GEAR OIL: F160A : Inspection
INFOID:0000000005248751
OIL LEAKAGE
Make sure that oil is not leaking from final drive assembly or around it.
OIL LEVEL
: Vehicle front
Standard
A
: 162 mm (6.38 in)
B
: 245 mm (9.65 in)
C
: 185 mm (7.28 in)
PDIA0772J
Limit
Propeller shaft runout
: Refer to
.
PDIA0477E
: Vehicle front
Standard
A
: 162 mm (6.38 in)
B
: 270 mm (10.63 in)
C
: 185 mm (7.28 in)
JSDIA0812ZZ
MA-34
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
• Remove filler plug (1) and check oil level from filler plug mounting
hole as shown in the figure.
CAUTION:
Never start engine while checking oil level.
• Set a gasket on filler plug (1) and install it on final drive assembly.
CAUTION:
Never reuse gasket.
FRONT DIFFERENTIAL GEAR OIL: F160A : Draining
INFOID:0000000005248752
1.
Stop engine.
2.
Remove drain plug (1) and drain gear oil.
3.
Set a gasket on drain plug (1) and install it to final drive assem-
bly and tighten to the specified torque. Refer to
CAUTION:
Never reuse gasket.
FRONT DIFFERENTIAL GEAR OIL: F160A : Refilling
INFOID:0000000005248753
1.
Remove filler plug (1). Fill with new gear oil until oil level reaches
the specified level near filler plug mounting hole.
2.
After refilling oil, check oil level. Set a gasket to filler plug (1),
then install it to final drive assembly. Refer to
CAUTION:
Never reuse gasket.
REAR DIFFERENTIAL GEAR OIL: R200
REAR DIFFERENTIAL GEAR OIL: R200 : Inspection
INFOID:0000000005248754
OIL LEAKAGE
• Make sure that oil is not leaking from final drive assembly or around it.
OIL LEVEL
JPDID0188ZZ
JPDID0189ZZ
Oil grade and Viscosity
: Refer to
.
Oil capacity
: Refer to
.
JPDID0188ZZ
CHASSIS MAINTENANCE
MA-35
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
• Remove filler plug (1) and check oil level from filler plug mounting
hole as shown in the figure.
CAUTION:
Never start engine while checking oil level.
• Set a gasket on filler plug (1) and install it on final drive assembly.
DLN-211, "2WD : Exploded View"
(AWD).
CAUTION:
Never reuse gasket.
REAR DIFFERENTIAL GEAR OIL: R200 : Draining
INFOID:0000000005248755
1.
Stop engine.
2.
Remove drain plug (1) and drain gear oil.
3.
Set a gasket on drain plug (1) and install it to final drive assem-
bly and tighten to the specified torque. Refer to
DLN-224, "AWD : Exploded View"
(AWD).
CAUTION:
Never reuse gasket.
REAR DIFFERENTIAL GEAR OIL: R200 : Refilling
INFOID:0000000005248756
1.
Remove filler plug (1). Fill with new gear oil until oil level reaches
the specified level near filler plug mounting hole.
2.
After refilling oil, check oil level. Set a gasket to filler plug (1),
then install it to final drive assembly. Refer to
DLN-224, "AWD : Exploded View"
(AWD).
CAUTION:
Never reuse gasket.
REAR DIFFERENTIAL GEAR OIL: R230
REAR DIFFERENTIAL GEAR OIL: R230 : Inspection
INFOID:0000000005248757
OIL LEAKAGE
Make sure that differential gear oil is not leaking from the rear final drive assembly or around it.
OIL LEVEL
JPDID0190ZZ
JPDID0191ZZ
Oil grade and viscosity
: Refer to
.
Oil capacity
: Refer to
JPDID0190ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст