Infiniti FX35, FX50 (S51). Manual — part 1409
PB-4
< PERIODIC MAINTENANCE >
PARKING BRAKE SHOE
PARKING BRAKE SHOE
Adjustment
INFOID:0000000005234466
1.
Adjust parking brake pedal stroke. Refer to
PB-3, "Inspection and Adjustment"
2.
Perform parking brake break-in (drag on) operation by driving vehicle under the following conditions:
• Drive forward
• Vehicle speed: Approx. 30 km/h (19 MPH) set (constant and forward)
• Parking brake operating force: 365 N (37 kg, 82 lb) set contact
• Time: Approx. 35 sec.
CAUTION:
To prevent lining from getting too hot, allow a cool off period of approximately 5 minutes after
every break-in operation.
3.
After the break-in procedure, check parking brake pedal stroke of parking brake.
CAUTION:
If it is out of the specification, adjust again. Refer to
PARKING BRAKE CONTROL
PB-5
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
REMOVAL AND INSTALLATION
PARKING BRAKE CONTROL
Exploded View
INFOID:0000000005234467
Removal and Installation
INFOID:0000000005234468
REMOVAL
1.
Remove rear tires with power tool.
2.
Remove instrument lower panel LH. Refer to
3.
Disconnect parking brake switch harness connector.
4.
Remove adjusting nut and loosen front cable.
5.
Remove device assembly.
6.
Remove center console. Refer to
7.
Remove rear ventilator duct (with rear ventilation). Refer to
8.
Remove the center muffler and heat insulator. Refer to
9.
Remove propeller shaft. Refer to
(3F80A-1VL107),
(3F-R-2VL107).
10. Remove the heat insulator for rear propeller shaft.
11. Separate front cable from rear cable, and remove front cable and spring.
1.
Pin
2.
Rear cable (right side)
3.
Rear cable (left side)
4.
Spring
5.
Front cable
6.
Lock plate
7.
Return spring
8.
Stopper rubber
9.
Device assembly
10. Pedal pad
11. Adjusting nut
12. Parking brake switch
: Apply multi-purpose grease.
Refer to
for symbols not described on the above.
JPFIB0080GB
PB-6
< REMOVAL AND INSTALLATION >
PARKING BRAKE CONTROL
12. Remove parking brake shoe, and remove rear cable from toggle lever. Refer to
13. Remove rear cable mounting bolts and nuts, pull out rear cable from vehicle.
INSTALLATION
Install in the reverse order of the removal.
Adjustment
INFOID:0000000005234469
ADJUSTMENT AFTER INSTALLATION
Adjust the parking brake pedal stroke. Refer to
PARKING BRAKE SHOE
PB-7
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
PARKING BRAKE SHOE
Exploded View
INFOID:0000000005234470
Removal and Installation
INFOID:0000000005234471
REMOVAL
WARNING:
Clean any dust from the parking brake shoes and back plates with a vacuum dust collector. Never
blow with compressed air.
1.
Remove rear tires with power tool.
2.
Remove disc rotor. Refer to
BR-57, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal and
(1 piston type),
BR-61, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal and
(2 piston type).
CAUTION:
Parking brake completely in the released position.
3.
If disc rotor cannot be removed, remove as follows:
a.
Fix the disc rotor with wheel nuts and remove the adjusting hole plug.
b.
Using suitable tool, rotate adjuster (1) in the direction (B) to
retract and loosen brake shoe.
4.
Remove anti-rattle pins, retainers, anti-rattle springs, and return
spring, adjuster spring.
CAUTION:
Never drop the removed parts.
5.
Remove parking brake shoes, adjuster assembly, and toggle
lever.
CAUTION:
• The parking brake shoes for the front wheels are made of
different materials from those for the rear wheels. Never
misidentify them when removing.
• Never drop the removed parts.
INSTALLATION
1.
Back plate
2.
Parking brake shoe
3.
Adjuster
4.
Adjuster spring
5.
Return spring
6.
Anti-rattle spring
7.
Retainer
8.
Anti-rattle pin
9.
Toggle lever
: Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease.
JPFIB0046ZZ
JPFIB0007ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст