Infiniti FX35, FX50 (S51). Manual — part 1353
OIL FILTER
LU-9
< PERIODIC MAINTENANCE >
[VQ35HR]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
OIL FILTER
Removal and Installation
INFOID:0000000005245064
REMOVAL
CAUTION:
• Oil filter is provided with relief valve. Use genuine NISSAN oil filter or an equivalent.
• Be careful not to get burned when engine and engine oil may be hot.
• When removing, prepare a shop cloth to absorb any engine oil leakage or spillage.
• Never allow engine oil to adhere to drive belt.
• Completely wipe off any engine oil that adheres to engine and vehicle.
1.
Remove engine undercover with power tool.
2.
Using oil filter wrench [SST: KV10115801 (J38956)] (B), remove
oil filter.
INSTALLATION
1.
Remove foreign matter adhering to oil filter installation surface.
2.
Apply engine oil to the oil seal contact surface of new oil filter.
A
: 2WD models
: Vehicle front
JPBIA0252GB
A
: AWD models
: Vehicle front
JPBIA1828ZZ
SMA010
LU-10
< PERIODIC MAINTENANCE >
[VQ35HR]
OIL FILTER
3.
Screw oil filter manually until it touches the installation surface,
then tighten it by 2/3 turn (A). Or tighten to the specification.
Inspection
INFOID:0000000005245065
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level. Refer to
.
2.
Start the engine, and check there is no leakage of engine oil.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level, and adjust the level. Refer to
.
Oil filter:
: 17.7 N·m (1.8 kg-m, 13 ft-lb)
JPBIA0077ZZ
OIL FILTER BRACKET (AWD)
LU-11
< REMOVAL AND INSTALLATION >
[VQ35HR]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
REMOVAL AND INSTALLATION
OIL FILTER BRACKET (AWD)
Exploded View
INFOID:0000000005245066
Removal and Installation
INFOID:0000000005245067
REMOVAL
WARNING:
Be careful not to get burned, as engine oil may be hot.
1.
Remove engine undercover with power tool.
2.
Using the oil filter wrench [SST: KV10115801 (J38956)], remove oil filter. Refer to
.
CAUTION:
Never spill engine oil on drive belt.
3.
Remove connector bolt, and then oil cooler with water hoses connected.
4.
Disconnect oil pressure switch harness connector and oil temperature sensor harness connector.
5.
Remove oil filter bracket from oil pan (upper).
6.
Remove oil pressure switch and oil temperature sensor from oil filter bracket.
INSTALLATION
1.
Oil pan (upper)
2.
Gasket
3.
Gasket
4.
Oil temperature sensor
5.
Oil pressure switch
6.
Oil filter bracket
7.
Relief valve
8.
O-ring
9.
Oil cooler
10.
Connector bolt
11.
Oil filter
A.
Refer to
B.
Refer to
: Engine front
Refer to
for symbols in the figure.
JPBIA2011GB
LU-12
< REMOVAL AND INSTALLATION >
[VQ35HR]
OIL FILTER BRACKET (AWD)
• Install oil pressure switch as per the following:
- Remove old liquid gasket adhering to oil filter bracket.
- Apply liquid gasket and install oil pressure switch.
Use Genuine RTV Silicone Sealant or an equivalent. Refer to
GI-16, "Recommended Chemical Prod-
.
Inspection
INFOID:0000000005245068
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and add engine oil. Refer to
2.
Start the engine, and check there is no leakage of engine oil.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level again. Refer to
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст