Infiniti FX35, FX50 (S51). Manual — part 560
FRONT CASE AND REAR CASE
DLN-75
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: ETX13C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
16. Install snap ring (1) to main shaft.
CAUTION:
Never reuse snap ring.
17. Install snap ring (1) to front case.
CAUTION:
Never reuse snap ring.
18. Apply liquid gasket (1) to mating surface of rear case.
Use Genuine Anaerobic Liquid Gasket or equivalent. Refer to
GI-16, "Recommended Chemical Products and Sealants"
.
CAUTION:
Remove old sealant adhering to mounting surfaces. Also
remove any moisture, oil, or foreign material adhering to
application and mounting surfaces.
19. Set front case to rear case.
CAUTION:
Never damage the mating surface transmission side.
20. Tighten front case and rear case fixing bolts.
*: With harness bracket.
21. Install spacer to main shaft.
CAUTION:
Apply transfer fluid to spacer.
JPDIE0122ZZ
JPDIE0109ZZ
JPDIE0142ZZ
Bolts symbol
Quantity
A
14
T (TORX bolt)
1
JPDIE0108ZZ
DLN-76
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: ETX13C]
FRONT CASE AND REAR CASE
22. Apply transfer fluid to outside of rear oil seal, and install rear oil
seal to rear case with the drifts within the dimension (L) shown
as follows.
CAUTION:
• Never reuse rear oil seal.
• Apply petroleum jelly to oil seal lip.
• When installing, never incline rear oil seal.
23. Install companion flange while aligning the matching mark (A) of
main shaft with the mark (B) of companion flange.
24. Tighten self-lock nut to the specified torque with flange wrench
(A) (commercial service tool).
CAUTION:
Never reuse self-lock nut.
25. Apply transfer fluid to outside of main shaft oil seal, and install
main shaft oil seal until it is flush with the end face of front case
with the drift (A) [SST: ST30720000 (J-25405)].
CAUTION:
• Never reuse main shaft oil seal.
• Apply petroleum jelly to oil seal lip.
• When installing, never incline main shaft oil seal.
A
: Drift [SST: ST30720000 (J-25405)]
B
: Drift [SST: KV40104830 (
—
)]
L
: 6.7 – 7.3 mm (0.264 – 0.287 in)
JPDIE0116ZZ
JPDIE0060ZZ
JPDIE0131ZZ
JPDIE0118ZZ
FRONT CASE AND REAR CASE
DLN-77
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: ETX13C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
26. Apply transfer fluid to outside of front oil seal, and install front oil
seal until it is flush with the end face of front case with the drift
(A) [SST: ST27862000 (
—
)].
CAUTION:
• Never reuse front oil seal.
• Apply petroleum jelly to oil seal lip.
• When installing, never incline front oil seal.
27. Set gasket to drain plug. Install it to rear case.
CAUTION:
Never reuse gasket.
28. Set gasket to filler plug. Install it to rear case.
CAUTION:
• Never reuse gasket.
• After oil is filled, tighten filler plug to specified torque.
VQ35HR : Inspection
INFOID:0000000005249120
Check items below. If necessary, replace them with new ones.
CASES
• Contact surfaces of bearing for wear, damage, etc.
• Damage and cracks of case.
BEARING
Damage and rough rotation of bearing.
SHAFT
Damage, peeling, dent, uneven wear, bending, etc. of shaft.
GEARS AND CHAIN
JPDIE0119ZZ
JPDIE0120ZZ
PDIA0300E
JPDIE0143ZZ
DLN-78
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: ETX13C]
FRONT CASE AND REAR CASE
• Excessive wear, damage, peeling, etc. of gear and chain.
• Cracks, damage, wear, etc of drive chain.
VK50VE
VK50VE : Exploded View
INFOID:0000000005249121
JPDIE0136ZZ
1.
Plug
2.
Drive chain
3.
Front drive shaft rear bearing
4.
Front drive shaft
5.
Front drive shaft front bearing
6.
Sprocket
7.
Needle bearing
8.
Main shaft
9.
Oil pump
10. Spacer
11.
Steel ball
12. Snap ring
13. Snap ring
14. Main shaft bearing
15. Front case
16. Main shaft oil seal
17. Front oil seal
18. Spacer
19. Snap ring
20. Circlip
21. Electric controlled coupling
JPDIE0196GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст